Installation Of The Tow Ready Tail Light Isolating Diode System # TR118821 On A 2021 Jeep Gladiator
Published 12/21/2021
Products Featured in This Question
Question:
How do I install this on my gladiator
asked by: Robert S
Expert Reply:
To install the Tow Ready Tail Light Isolating Diode System with 4-Pole Connector # TR118821 on your 2021 Jeep Gladiator you'll need to complete the following steps:
1. Locate the towed vehicle left and right STOP/TURN and TAIL signal wires. This can be done using the Circuit tester # PTW2992. Cut each wire as indicated in FIG. 1 and attach mating quick-disconnect terminals.
2. Attach the adapter unit to a convenient location in the rear of the towed vehicle using adhesive tape on bottom of each unit.
3. Connect the towed vehicle input wires as follows:
DRIVER SIDE:
Left STOP/TURN (yellow) at B.
Left TAIL (brown) at A.
PASSENGER SIDE:
Right STOP/TURN (green) at D.
Right TAIL (brown) at C.
4. Connect the output wires from the adapter to the towed vehicle lamp wiring as follows:
DRIVER SIDE:
Left STOP/TURN (yellow) at F.
Left TAIL (brown) at E.
PASSENGER SIDE:
Right STOP/TURN (green) at G.
Right TAIL (brown) at H.
5. Attach ring terminal (supplied) to white ground wire of 4-way flat input connector (adjust length of wire to nearest screw on chassis). Use existing screw (if possible) to ground white wire.
6. Connect 4-way flat input connector to 4-way flat cable (supplied) and route to towing vehicle mating 4-way flat connector.
7. Test for proper operation of the towed vehicle not connected to towing vehicle. Test for proper operation of the towed vehicle when connected to towing vehicle. You can complete this test using the Circuit Tester # PTW2992.
Once complete I recommend using a mounting bracket like # 18144 with # C57202 to mount the 4-pole connector to the hitch of your Gladiator to prevent it from flapping around or dragging on the ground.
(click to enlarge)
(click to enlarge)
Featured Help Information
Miscellaneous Media
Continue Researching
- Article: Flat Towing Package for 1998-2006 Jeep Wrangler
- Video: How to Install the Roadmaster Universal Hy-Power Diode Wiring Kit on a 2021 Jeep Wrangler
- Q&A: Recommended Flat Towing Setup for a 2007 Jeep Wrangler
- Shop: Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Way to 6-Way Coiled Adapter Cord
- Shop: Roadmaster Direct-Connect Base Plate Kit - Removable Arms
- Shop: Base Plate for Tow Bar
- Shop: Vehicle Tow Bar Wiring
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Video: An In-Depth Look at the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Q&A: Which is Better Roadmaster or Blue Ox Tow Bar
- Shop: Trailer Wiring
- Shop: Blue Ox Patriot Portable Flat Tow Brake System - Proportional
- Video: An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Search Results: base plate for tow bar
- Video: Breaking Down the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Shop: Roadmaster Battery Charge Line Kit for Towed Vehicles
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: How to Measure for Trailer Hitch Drop
- Search Results: tow bar
- Q&A: Replacing 6-Way on Trailer With 7-Way Connector
- Search Results: vehicle tow bar wiring
- Shop: Vehicle Tow Bar Brake System
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
on Flat Tow Wiring Harness
