Looking For Replacement Parts For A Quality S Weight Distribution System

Question

Question:

I just need a pair of frame brackets for a chain style weight distribution system. I can use the balls for the sway bar too. Attached are pics of what I have.

asked by: Brad

1

Helpful Expert Reply:

Quality S is not a brand of weight distribution system we carry, so I cannot say if replacements that we have from other brands will fit properly, unfortunately. I was also unable to find any information about this brand.

With that said, the best recommendation I can make is to replace the system with a brand that is still being produced and has replacement parts readily and easily available. The Reese Steadi-Flex Weight Distribution System # RP66560, as an example, can have literally any and every piece replaced and most parts can be sourced at local trailer supply shops/stores. This is also a system I recommend a lot as it does an extremely good job with sway control. Though on the expensive side, I do highly recommend it.

If you can send me the pictures you have, I can see if we have anything that will be close. But again, due to us not carrying the Quality S line, I cannot 100% guaranty the compatibility.

expert reply by: Lazer S

1

Quality S Weight Distribution System Head
(click to enlarge)

Quality S Weight Distribution System Friction Sway
(click to enlarge)

Quality S Weight Distribution System Spring Bars
(click to enlarge)

Brad

12/22/2021

I just need a pair of frame brackets for a chain style weight distribution system. I can use the balls for the sway bar too. Attached are pics of what I have.

Lazer S.

12/22/2021

The Reese Replacement Lift Brackets with Handle # RP6637 will have no issue working with your Quality S weight distribution system and they will include everything you need for that. Replacing the balls for your friction sway control device is another story. There is a possibility that the Reese Replacement Ball for Friction Sway-Control System # RP58060 and Replacement Ball-Plate Assembly # RP58062 will work perfectly fine, but as these are different brands, I cannot say that for sure, unfortunately. With that said, I recommend replacing that whole part with the Reese Friction Sway Control Kit # 83660. This way there will be no doubts of everything working. I think this will be the better way to go.

Answer 1

Because your trailer is fairly heavy, I would recommend you go with 2 of the #58392 lift brackets. The 58392 has extra gusseting welded to it for reinforcement, and would be better suited to a heavier trailer like yours, because the spring bars will…

view full answer...

Answer 2

The Replacement Heavy Duty Snap-Up Bracket #58392 does not require drilling to install as it basically can set on frame members that are up to 2-1/4 inches in width and uses a set screw to secure instead.

view full answer...

Answer 3

Thank you for all of the pictures. I do have a solution for you but when I reached out to my contact at Reese he said that you have the older SC weight distribution (WD) system and there aren't any replacement bars that will fit your application.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Looking For Replacement Parts For A Quality S Weight Distribution System

Featured Help Information

Miscellaneous Media

Continue Researching