Where are Bracket Height Measurements of Fulton XLT Marine Jack Measured From

Question

Question:

22inch of travel and 9.75inch retracted means nothing, unless we know where youre measuring from. If it sits 9.75inch below the trailer tongue and then can extend 22, does that mean I can get the bottom of my trailer tongue 31.75inch off the ground?

asked by: Tom S

0

Expert Reply:

The bracket height dimensions of the Fulton trailer jack # F141401 that you referenced are measured from center of the mounting bracket of the jack down to the bottom of the jack foot. So it would be 9-3/4 inches from center of bracket to ground retracted and 31-3/4 inches when extended. This does mean you could get your trailer's tongue 31-3/4 inches off of the ground.

expert reply by: Jameson C

0

Answer 1

Thank you for providing the picture of your existing mount. This was helpful to idenfication and I have attached it to this post. As you mentioned, the 90 degree snap in holes are 3" apart from center to center. It may be helpful to note that…

view full answer...

Answer 2

Your best bet is going to be hardware kit #F0933325S00. The bolt is a 1/2 inch coarse threaded bolt with matching nut and bushing. But it sounds like the nut or bolt is backing out on your assembly. This could mean the lock washer is shot. You could…

view full answer...

Answer 3

The only trailer jack that will work with your existing mounting bracket and not contact the boat with a full rotation of the handle is the Fulton Bolt-Thru Swivel Marine Jack part #F1411300301. I understand this does not have the sharkskin coating…

view full answer...

Answer 4

I recommend Dutton-Lainson Round Swivel Jack w/ 2" Wide Wheel - Sidewind - 12" Lift - 1,500 lbs Item #DL22210. This jack allows you to bolt through the frame however, it comes with brackets that will fit where your existing jack sits. The…

view full answer...

Answer 5

Most likely the #FXP15W would work great as a replacement for what you have but it's hard to verify that without seeing how what you have now mounts to the trailer. If you could send me a picture of what you have I can verify.

view full answer...

Answer 6

To replace your older Fulton Magnum Series 1500 Pound Jack, I recommend the Fulton Bolt-Thru Swivel Marine Jack #FXP15W. This 1,500 pound swivel jack is what Fulton replaced the Magnum Series with, so it should use the same mounting design as your…

view full answer...

Answer 7

Fulton bolt-through trailer jack #F1411300301 is the only Fulton jack that mounts using that 1 center bolt. Since your old jack was a Fulton it must either be this same jack or an earlier model but they use the same mount. The mount in question and…

view full answer...

Answer 8

According to Dexter, this is a 3,750 lb torsion axle with a 90.3" hub face measurement. More than likely your axle uses #L68149 and #L44649 bearings with a #168255TB grease seal. You will need to verify this information since Dexter did not have…

view full answer...

Answer 9

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Answer 10

Alejandro, in order to find out what size brakes your boat trailer needs you can either pop off your hub and measure the width and depth of the drum, or, you can let me know what size axle you have and we'd be able to find out what size brakes…

view full answer...

Answer 11

The best way to jack up a boat trailer with torsion axles, or straight axles for that matter, is to use a trailer jack that is rated high enough for the weight of the trailer at the point the jack is installed. Going with a higher capacity than…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Where are Bracket Height Measurements of Fulton XLT Marine Jack Measured From

Continue Researching