Recommended Trailer Hitch Receiver for 2003 GMC Yukon

Question

Question:

Will this hitch fit around the lower rear bumper cladding of my 2003 GMC Yukon?

asked by: John C

0

Expert Reply:

Yes, the Curt Trailer Hitch Receiver item # C15324 will fit your 2003 GMC Yukon. Depending on your trim package and how low it goes below your bumper you may have to cut an opening in your trim for the receiver to be accessed.

expert reply by: Jerred H

0

yukon xl curt class v
(click to enlarge)

Answer 1

I can't recommend you drill into any hitch including the Curt Hitch part #C15324 for the install of anything including a trailer wiring bracket. What I would recommend is a mounting bracket that attaches to the hitch's cross tube like the…

view full answer...

Answer 2

I spoke with my contact at Curt and trailer hitch #C15324 has a 3 inch x 3 inch cross tube. The mounting bracket #18159 would be the best options since it does not reach around 3 sides of the tube, just 2. I have linked a video showing installation…

view full answer...

Answer 3

When installing the Curt Trailer Hitch Receiver #13322 on your 2005 Chevy Silverado 1500, you will need to torque the rear M14 bolt to 126 lb-ft and all the 1/2 inch fasteners to 110 lb-ft. I have attached an installation video that you can use for…

view full answer...

Answer 4

You can install a different hitch or suspension enhancement but the vehicle capacity is set in stone. Adding the above mentioned parts or other parts won't increase the capacity of the vehicle. The 12,000 pounds you see in the owner's manual…

view full answer...

Answer 5

As for comparing the Timbrens #TGMRCK15S to the Roadmaster Active Suspension Custom Leaf Spring Enhancement Kit #RAS54FR on your 2021 Chevy Silverado 1500 (4x4), the answer really depends on how much you tow or need suspension support for your Chevy.…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Recommended Trailer Hitch Receiver for 2003 GMC Yukon

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching