Sensor Relocation Kit For Bull Bar On 2021 Ford F-150

Question

Question:

do your company have a sensor relocation kit that fit bull bars? i have f-150 ford lariat crewcab thanks

asked by: Richarw T

0

Expert Reply:

The Parking Sensor Relocation Kit for Westin Grille Guard # 40-0015S is designed to be used with the Westin Sportsman Grille Guard # 40-3555 and the Westin HDX Winch Mount Grille Guard with Punch Plate # 57-93555 this is due to the sensors needing a flat surface to mount to.

If you want to use this kit # 40-0015S on a bull bar like the Westin Ultimate Bull Bar with Skid Plate # 32-3925, you will need to fabricate brackets.

That being said, we do not currently offer a sensor relocation kit for bull bars.

expert reply by: Bryce D

0

Answer 1

The Parking Sensor Relocation Kit for Westin Grille Guard #40-0015S that you mentioned is actually designed to work with the 2009 - 2018 Dodge Ram 1500, and will not work with your 2014 GMC Sierra 1500. Instead, take a look at the: -Stainless Steel…

view full answer...

Answer 2

The Bulldog Winch Master Power Shut-Off Kit #BDW20079 is rated up to 200 amps. And the power wire included with the kit is indeed 2 gauge.

view full answer...

Answer 3

A diode like the part #RM-690 is a great idea but the only issue is that is has a max load of 85 amps. A standard 5,000 lb winch, like the ComeUp DV-5000si #CU645010, will greatly exceed the 85 amp rating of the diode so it would be useless. What you…

view full answer...

Answer 4

Due to how the Bulldog Winch 500 Amp Shut-Off Switch #BDW20248 attaches to the wiring using studs that you could use basically any ring terminal. This is rated for 500 amps though so a very heavy gauge wire was intended to be used so I'd assume a…

view full answer...

Answer 5

We have two options for you to consider. We have the Bulldog 500 amp switch part #BDW20248 which would work well or we have the 400 amp switch part #BDW20247 instead which has a removable key on it which would act as a theft deterrent possibly. Both…

view full answer...

Answer 6

The studs of the Bulldog Winch Shut Off Switch part #BDW20248 are 5/16 inch in diameter.

view full answer...

Answer 7

If you are anticipating needing a switch that is rated for 350 amps then we will need to find you a different switch as the Master Power Shut-Off Kit #BDW20079 is only rated for up to 200 amps. For your application I recommend using the 500 Amp…

view full answer...

Answer 8

We do! If you don't already have the disconnect switch then you can use the Demco Battery Disconnect Switch #DM63FR which comes with a lead. Otherwise we have leads like the 13" Deka Cable #DW01485 that can be used to bridge the gap between…

view full answer...

Answer 9

The Bulldog Winch 500 Amp Shut-Off Switch - Metal Housing #BDW20248 will operate up to and at 500 amps whether it is intermittent use or continuous. The 500 Amp battery disconnect switch should only be used for powering on and off the main power line…

view full answer...

Answer 10

The Demco Battery Disconnect Switch #DM63FR has the following ratings: - 300 Continuous Amps Rate - 500 Cold Cranking Amps I confirmed this with my contact at Demco.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Sensor Relocation Kit For Bull Bar On 2021 Ford F-150

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching