Installation Question for Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit # RM-15267
Updated 11/09/2021 | Published 11/05/2021
Question:
I have a 2021 Jeep Wrangler and I ordered the Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Way to 6-Wire Hybrid Cord. I routed it already towards the back no problem. I split off the back wire and grounded it to the frame. My question is: I have watch several videos on your site. The video shows the bundle being routed, and the white wire being grounded just as I did. But when the wire bundle is routed to the dr. side taillight, it shows the white wire again that was just cut off and grounded??? What is the white wire attached too? So the yellow and brown route to the dr. side / and the green route to the pass side correct? What other wire if any get routed to the pass side? Very confused!
asked by: John S
Expert Reply:
You are correct, once you cut the white wire to ground the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit # RM-15267 you will use that part of the white wire you cut off. You will wrap one end of the new white wire around the yellow and brown wire and route that bundle to the driver side taillight. Once you get bundle to the taillight you will you will twist the brown and white together and that gets connected to a diode.
The other end of the new white wire will be routed with the green wire to the passenger side. The new green wire will then plug into the diode of the lime green wire. The new white wire will plug into the diode of the white/orange stripe wire.
I have attached a video showing the installation of the # RM-15267 on a 2019 Jeep Wrangler. This video does a good job of showing how the white wire that you cut off is used.
Product Page this Question was Asked From
Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Way to 6-Way Coiled Adapter Cord
- Flat Tow Wiring Harness
- Splices into Vehicle Wiring
- Diode Kit
- Universal Fit
- 7 Blade to 6 Round
- Roadmaster
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: roadmaster 055~3
- Shop: Vehicle Tow Bar Wiring
- Shop: Roadmaster Tow Bar Cover
- Shop: Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Way to 6-Way Coiled Adapter Cord
- Shop: 12 Volt Outlet Kit, 20 amps
- Shop: Vehicle Tow Bar Brake System
- Shop: Roadmaster Stop Light Switch Kit
- Q&A: Solution for 7-Way to 6-Way Adapter where Vehicle Has Center Pin as 12 Volt Power
- Shop: Go Power Overlander Expansion Kit - 200 Watt Solar Panel
- Q&A: How To Install The Roadmaster Brake-Lite Relay Kit On A 2022 Jeep Wrangler Limited Sport
- Q&A: Do I Need a Brake Light Relay to Flat Tow a 2020 Jeep Wrangler Rubicon?
- Video: Setting up the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit on a 2013 Jeep Wrangler
- Shop: Roadmaster Battery Charge Line Kit for Motorhomes
- Video: In-Depth Review of the 3-Piece Electrician Tool Set
- Video: Beginner’s Guide to Installing the 12 Volt Outlet Kit, 20 amps on a 2015 Jeep Wrangler
- Video: Setting up the 12 Volt Outlet Kit, 20 amps on a 2016 Jeep Wrangler
- Video: An In-Depth Look at the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Shop: Bauer NE RV Entry Door Lock for Trailers - Bluetooth - Right Handed
- Video: Review of Bauer Products RV Door Locks - Entry Door - BA93UR
- Video: Checking Out the Go Power MC4 Output Cable with Male and Female Connectors
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Search Results: trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Q&A: Which is Better Roadmaster or Blue Ox Tow Bar
- Search Results: base plate for tow bar
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
on Flat Tow Wiring Harness
