Dimensions Of The Replacement Trailer Brake Magnet BP01-068

Question

Question:

I read that the magnet thickness is 3/4. What is the OD? What size is the center hole?

asked by: Scott

0

Expert Reply:

I went out to our warehouse and measured an outside diameter of 1 7/8" for the Replacement Trailer Brake Magnet Kit # BP01-068 and 1/2" x 1/2" for the center hole.

expert reply by: Bryce D

0

Brake Magent Dimensions
(click to enlarge)

Answer 1

Buongiorno! We do carry Replacement Magnet Kit for 7" Electric Trailer Brake Assemblies - 2,000 lbs Item #AKBRKR-M7. However, it looks like the center mounting hole on yours is round, whereas ours uses a square/rectangular hole. It doesn't…

view full answer...

Answer 2

First I want to make sure you verify your channel mount for the Demco Trailer Coupler #DM14040-81 has a 21K or larger capacity as often times they are less like the Demco #DM15349-52 which often times people look at and think it is a channel mount…

view full answer...

Answer 3

Good question; the bolts in the Hardware Kit for Demco Adjustable Channel Mount Couplers #DM6166 should be torqued to 150 lb-ft during install of a Demco coupler like #DM14040-81 to a bracket like #DM66134.

view full answer...

Answer 4

The Replacement Magnet Kit for 7" Electric Trailer Brake Assemblies part #AKBRKR-M7 and Replacement Trailer Brake Magnet Kit for 7" Brake Assemblies part #BP01-068 are both round brake magnets for 7", 2,000 lb trailer braking…

view full answer...

Answer 5

We do not have the exact magnet clip for 7 inch brakes so #AKBRKR-MC could work but it may need to be modified to fit. The other option is to replace the magnet which comes with a new spring and clip, #BP01-068. Without the clip the magnet can come…

view full answer...

Answer 6

Are there any visible signs of wear on the magnets like exposed windings then that would indicate they need replacing. Magnets can go bad without showing visible signs of wear though. To see how to troubleshoot them check out the help article I…

view full answer...

Answer 7

The 7 inch Dexter Brake Assemblies like the part #23-48 do use clips to attach the magnets to the assemblies. I went and pulled one from our warehouse and found that in order to attach the magnet to the arm you would need to slide the magnet over the…

view full answer...

Answer 8

Yes the brake magnets part #AKBRKR-M7 will work in place of the K71-057-00 #BP01-068 magnets your trailer has currently.

view full answer...

Answer 9

Yes, you are able to replace one of your awning arms. According to the tag you sent you will need the Replacement Support Arm Assembly #LC281154. This will allow you to replace either awning arm. You will be able to transfer the head off your current…

view full answer...

Answer 10

There are certainly a few troubleshooting steps that we can try that will tell us where the issue lies. Changing or charging a vehicle battery with the brake controller connected can cause different and random issues. It could be possible that…

view full answer...

Answer 11

Brake magnets for 12 inch brake assemblies should have an ohms reading that falls within the range of 3.0 to 3.8. The 3.7 ohms reading on your brake magnets does not indicate that the brake magnets need to be replaced. If you are experiencing…

view full answer...

Answer 12

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Dimensions Of The Replacement Trailer Brake Magnet BP01-068

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching