Replacement Head for Reese Weight Distribution # 61241

Question

Question:

My Reese weight distributing hitch is from 2003. The part number on the hitch head is 61241. One of the tabs snapped off that holds the bar in place. Is the 58112 compatible/appropriate replacement head?

asked by: E L

0

Expert Reply:

We've checked with Reese in the past and they have told us that the # RP58112 was once the 61241 so this would work great as a replacement head.

expert reply by: Jameson C

0

Answer 1

Yes, you can use the Reese spring bars that are stamped 750 with the Replacement Head for Reese Weight Distribution System - Round Bar item #RP58112. For replacement balls you will want 2" Hitch Ball - 1-1/4" Diameter x 2-5/8" Long…

view full answer...

Answer 2

The Replacement Head for Reese Weight Distribution System - Round Bar #RP58112 will work with all Reese round bars that insert and twist for installation. I've attached a photo to assist. As long as the top of your round bars look like #PS58440,…

view full answer...

Answer 3

The weight distribution hitch head assembly where your round spring bar installs will usually have some branding or other information such as a safety/warning sticker, or possibly a number cast into it. The remaining spring bar may itself have a part…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Replacement Head for Reese Weight Distribution # 61241

Continue Researching