How Many Bolts Hold Head of Demco Recon Hitch to Base

Question

Question:

Im starting to see pictures of the Recon Gooseneck hitch with two bolts at the bottom to tighten down the upper unit. Is this a new revision?

asked by: William L

1

Helpful Expert Reply:

The current version of the Demco Recon Gooseneck to Fifth Wheel Hitch # DM8550045 does have two bolts that hold the upper portion of the hitch to the base like in the picture you attached. The older version only used a single bolt.

expert reply by: Jameson C

1

Recon Hitch with Two Bolts Holding Head
(click to enlarge)

Answer 1

When adjusting the height of a pin box such as #LC1191191 it is important to support the pin box when removing the bolts. I recommend 2 or 3 buddies to give you a hand and make sure no one is beneath the pin box while raising or lowering it. With the…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 6

Hey Tom, congrats on the new truck! Typically when we hear that someone has the OEM tow prep package they mean the puck system. This is going to be five circular holes built into the bed of your Ram truck and is by far the best way to attach a 5th…

view full answer...

Answer 7

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Answer 10

When installing the pivot arms on your B&W Companion OEM 5th Wheel Hitch for Ram Towing Prep Package - Dual Jaw - 25,000lbs Item #BWRVK3600 you'll want to ensure that you have 6" of clearance between the bed rails and the nose of your…

view full answer...

Answer 11

Hey Steve, congrats on the new truck. Since your 2026 Ram 3500 has the factory puck system, you'll want the PullRite SuperGlide 5th Wheel Hitch item #PUL28RR. The PullRite SuperGlide 5th Wheel Hitch item #PUL28RR has a 24,000 lbs capacity and…

view full answer...

Answer 12

To determine if the MORryde Cushioned 5th Wheel Pin Box for 14K to 18K Trailers w/ Lippert 1621 and 1621HD #MR84VR will fit your trailer you'll need to first determine your trailer's bolt pattern. There will typically be a sticker (pictured…

view full answer...

How Many Bolts Hold Head of Demco Recon Hitch to Base

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching