Replacement Clearance Lights for 2012 Forest River Sunseeker Class C

Question

Question:

Hello I am looking to replace a light on the front top of my RVs cab. I looked at your websit but was not able to identify. Could you please help, so I can buy one on your site. I have uploaded a picture in this message. It is Forest River Sunseeker 2012. Class C. Attached a sample picture. Thank you

asked by: Ahmed

0

Expert Reply:

We do not have information that tells us specifically what lights are on your 2012 Forest River Sunseeker, so the best way to determine what's going to fit is by providing measurements or a part number off the existing lights. With that said, it looks like you may have something similar to the Optronics LED Clearance or Side Marker Light w/ Reflex Reflector - 6 Diodes - Oval - Amber Lens # MCL31AB. The # MCL31AB is 4" long x 2-1/16" tall x 1" deep with mounting holes 3" apart (center on center), so you'll want to confirm these dimensions compared to your existing lights or opening.

If you've got lights that are a different dimension and can let me know, I might be able to locate a better alternative that would work.

expert reply by: Erik B

0

Sunseeker clearance lights
(click to enlarge)

MCL31AB dimensional drawing
(click to enlarge)

Answer 1

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 2

The LED Trailer Clearance or Side Marker Light w/ Reflex Reflector - 3 Diodes - White Base - Red Lens #MCL32RB does have just the lens available as part #A32RB. If that is your light, you will be able to just swap the lens. I've linked the page…

view full answer...

Answer 3

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

The Optronics LED Clearance or Side Marker Trailer Light is available in Red #MCL0030RBB and Amber #MCL0030ABB. These are the closest replacements to the Glo Brite 122r/122y lights you have. The lights only have one LED diode versus the 3 in your…

view full answer...

Replacement Clearance Lights for 2012 Forest River Sunseeker Class C

Product Page this Question was Asked From

Continue Researching