Correct B&W Turnoverball Underbed Gooseneck Trailer Hitch for a 2010 Ram 3500 Mega Cab

Question

Question:

Hello, 2010 Ram 3500 6.7 diesel megacab Single wheel rear axle. will the BWGNRK1313 work in this truck?

asked by: Jeff P

0

Expert Reply:

The correct B&W Turnoverball Underbed Gooseneck Trailer Hitch for a 2010 Ram 3500 Mega Cab is part # BWGNRK1308. This works on both gas and diesel engine models when used on a Mega Cab. The part # BWGNRK1313 is not compatible with Mega Cab models.

expert reply by: Conner L

0

Answer 1

Hey Terry! I have some awesome news for you. The B&W Turnoverball #BWGNRK1313 will absolutely, 100% fit and work for your 2012 Ram 3500 Diesel Mega Cab. In fact, this particular model is specifically designed for the diesel engine models of your…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 4

Hey Kent! Your Alliance Avenue already has some great suspension components with the MORryde CRE3000 equalizers, wet bolt kit, and Rota-Flex pin box. I wouldn't replace any of those unless you're experiencing a specific problem. The next…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Answer 8

Hey Fred! You will need to take some measurements to determine if you will have enough clearance with the B&W Gooseneck Pin Box #BW23RV. You can use the following formula: (A + B) - C = Clearance A = Distance from the gooseneck ball center to the…

view full answer...

Answer 9

Hello Steven, You will want to use a 3 1/2" bit as you need a 3 1/2" hole for the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs #BWGNRK1320. I attached an image where it goes over the size…

view full answer...

Answer 10

Hey Sean, welcome back! We do have a video showing the B&W Turnoverball #BWGNRK1320 being installed on a 2022 Ram 3500. I have provided a link to the video below. We don't have any videos showing how to remove the factory puck system though,…

view full answer...

Answer 11

Hey Kendall, we have just what you are looking for with the MORryde GooseTech fifth wheel to gooseneck adapter part #MR97MV. This is the correct fit to replace your Lippert 1621 pin box and has the correct weight rating as well. But the main reason I…

view full answer...

Correct B&W Turnoverball Underbed Gooseneck Trailer Hitch for a 2010 Ram 3500 Mega Cab

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching