Correct Wiring for Bulldog Powered-Drive Kit # BD1824200100

Question

Question:

I need a wiring diagram for this. I misplaced mine. Thank you

asked by: Paul G

0

Expert Reply:

The wiring for the Bulldog Powered-Drive Kit # BD1824200100 is as follows for the four wires in the wiring harness.

The Black wire from the battery goes to the Black wire on the harness
The Red wire from the battery goes to the Red wire on the harness

The Black wire from the motor goes to the Green wire on the harness
The Red wire from the motor goes tot he White wire on the harness

The photo of the wiring diagram shows you the exact wiring connections.

expert reply by: Lori W

0

click to enlarge

Chance T.

5/29/2020

Does it matter where the wires go in the junction box?

Chris R.

6/1/2020

As long as the wire connections are correct (as shown above) it doesn't matter which terminals are used for each function inside the junction box.

Answer 1

I have a solution for you, but the #BD1046130-00 is designed for a single speed electric jack. To replace landing gear with the motor 1046104 you'll want to use the Replacement Dual Output Motor for Bulldog Electric 5th Wheel Landing Gear…

view full answer...

Answer 2

I attached pictures that show how the switches of the Bulldog Powered Jack #BD500187 get wired.

view full answer...

Answer 3

The motor that fits Bulldog jack #BD182701 is powered drive kit #BD1824200100. The shaft on the jack is 1 inch in diameter and the pin hole for the crank is approximately 5/16 of an inch. The motor mounts to the side of the jack as you can see in the…

view full answer...

Answer 4

I attached a picture that shows the wiring diagram to use Bulldog Powered-Drive Kit for Single-Speed Jacks #BD1824200100 for you to check out David.

view full answer...

Answer 5

Hi Thomas, From what information I could find, the roll pins are 1/4" in diameter and 1 1/4"long. We don't have just the roll pins available, but we do have a whole repair kit for the etrailer and Ram 12K series jacks, which is the…

view full answer...

Answer 6

Hey, Ryan! At this time we do not have a video replacing spring part #TJD-12000-RSP on the etrailer jack part #e66FV. Hopefully we can get one done soon.

view full answer...

Answer 7

Hey Zachary, What kind of specs are you needing for the Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks #TJD-12000-RSP? It's designed to work with 10k rated etrailer and Ram square jacks. While retracted the spring is…

view full answer...

Answer 8

Hey Hoss, looks like you ordered the part #BD1824200100 from us back in December. Hows the battery on your trailer? It have a good charge on it? Is any of the wiring loose? Those are the two biggest culprits of this issue so I'd start there. Have…

view full answer...

Answer 9

Without any identifying information on your trailer jack it's just a guessing game at this point. If you do end up taking your jack apart and it's rated for 10K then you just need to measure the spring to ensure the Replacement Return Spring…

view full answer...

Answer 10

I went ahead and reached out to RAM and they explained to me that to re-install your inner leg to your RAM jack like the Square Direct Weld Jack - Drop Leg w/ Spring Return #TJD-12000SP-R2NH, you are going to need to re-install the lower pin, replace…

view full answer...

Answer 11

To replace just the motor for your 12000 lb Bulldog single-speed jack (like #BD182815) you will just need motor #BD1046130-00. I've attached a video of the motor being installed for your convenience. To replace the dual-output motor for Bulldog…

view full answer...

Answer 12

There are several places water can get into any given jack. Water should be able to drain out though. If the exit points which would be at the lowest point are clogged then the water would not be able to exit. You could use a jack cover like…

view full answer...

Correct Wiring for Bulldog Powered-Drive Kit # BD1824200100

Continue Researching