Dimensions Of The Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks
Updated 10/04/2024 | Published 10/03/2024 >
Question:
TJD-12000-RSP Im looking for a replacement spring for my trailer landing legs and it should be similar to P/N above. I wanted to request specs on this item just to verify before purchase. thank you.
asked by: Zachary J
Expert Reply:
Hey Zachary,
What kind of specs are you needing for the Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks # TJD-12000-RSP? It's designed to work with 10k rated etrailer and Ram square jacks. While retracted the spring is 11-3/4" in length and the rings on each end add an extra 7/8" each to 11-3/4" that length for an overall length of 13-1/2". If you're needing some other specs then just let me know and I'd be happy to help.
Product Page this Question was Asked From
Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Hardware
- Springs
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Search Results: trailer axles
- Video: Review of etrailer Replacement Return Spring etrailer Ram Square Direct Weld Jack - TJD-12000-RSP
- Shop: Replacement Lower Spring for Rack'Em Double Barrel Trailer Tailgate Lift Assist - Qty 1
- Shop: Replacement Cutting Edge for Boss Snow Plows - Carbon Steel - 8' Long x 6" Tall
- Shop: Taskmaster Solid Center Wheel w/ -0.19 Offset - 17-1/2" x 6-3/4" Rim - 8 on 6-1/2 - Silver
- Search Results: trailer tires and wheels
- Shop: Tandem Axle Teardrop Fenders w/ Backing Plates - 15" to 16" Wheels - Qty 2
- Search Results: wheel
- Search Results: 7k brakes
- Shop: Bright Way Trailer Breakaway Kit with Charger, LED Tester, and 5 Ah Battery - Side Load
- Search Results: wire clip
- Search Results: rear spring hanger
- Search Results: single step
- Shop: etrailer Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 5,200 lbs to 7,000 lbs
- Q&A: Determining the Correct Spring Replacement on Sundowner Sunlight Stampede Gooseneck Trailer Jack
- Video: Review of Lippert Replacement Leveling Jack Service Kit - LC92CJ
- Video: A Closer Look at the Lippert High-Speed Power Stabilizer Jack
- Video: A Closer Look at the B and W Extend-A-Goose Gooseneck Coupler
- Video: What to Know About the B and W Extend-A-Goose Gooseneck Coupler
- Video: Buyers Products Heavy Duty Square Jacks Replacement Handle Installation - Big Tex Trailer
- Q&A: Dimensions of the Replacement Return Spring Part # TJD-12000-RSP
- Shop: Vehicle Engine Heaters
- Q&A: Replacement Return Spring for Bulldog Square Jacks
- Shop: Gooseneck Hitch
- Q&A: Replacing the Drop Leg Spring Loaded Pull Pin on a Bulldog 180 Series Square Jack
- Q&A: Replacement Parts for the Square Direct Weld Jacks
- Q&A: Trailer Jack and Coupler Recommendation for Featherlite Bumper Pull Trailer
- Q&A: Vertical Rise To Welds and Lowest Pin Hole on B&W Extend-A-Goose Gooseneck Coupler
- Video: Ultimate Overview of the Square Direct Weld Jack



Zachary J.
10/3/2024
Thats what i was wondering about. the landing leg set i'm working with is12K rated. The spring i'm looking for is 13" when retracted and 14-1/2" overall. Do you have anything that may work for my needs?