Troubleshooting Bulldog Powered Drive Kit that Is Slowly Stopping Working
Published 02/20/2025
Question:
Hello I purchase a bulldog trailer Jack before my trailer. I noticed the past few days. The Jack itself is starting to not work properly. Ill press extend or retract or the memory button a few times and it will do nothing, and sometimes it will work and sometimes it wont. Ive only had this For a few months.
asked by: Hoss F
Expert Reply:
Hey Hoss, looks like you ordered the part # BD1824200100 from us back in December. Hows the battery on your trailer? It have a good charge on it? Is any of the wiring loose? Those are the two biggest culprits of this issue so I'd start there.
Have you tried using the manual jack handle to raise and lower the jacks? Do they seem any more difficult than usual? That will let us know for sure if the problem is electrical or mechanical.
Continue Researching
- Shop: Trailer Hitch
- Shop: Class V Universal Weld-on Receiver Hitch and Brackets with 3" Drop
- Shop: Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2-1/2" Receiver - 44" Wide
- Q&A: 2-1/2 Inch Trailer Hitch Option For 2007 F-350 Super Duty With Utility Bed
- Q&A: Welding Tips For Trailer Accessories
- Shop: Phoenix Electric Trailer Jack - A-Frame - 18" Lift - 4,000 lbs
- Search Results: heavy duty receiver hitch
- Video: Feature Breakdown: Curt Class 5 Universal Weld-on Hitch w/ Brackets
- Shop: Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2-1/2" Receiver - 62" Wide
- Shop: Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide
- Shop: Square 2-Speed Trailer Jack w/ Handle - Drop Leg - Sidewind - 12-3/8" Lift - 10,000 lbs - Weld
- Shop: Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Search Results: bd500363
- Q&A: Troubleshooting Malfunctioning Bulldog Power Jack # BD500199
- Q&A: Dimensions Of The Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks
- Q&A: Do You Have a Video on How to Replace the Spring for the etrailer Square Direct Weld Jack e66FV
- Search Results: 20k hitch
- Q&A: Recommended Trailer Hitch For An Isuzu Box Truck With a 33.5 Wide Frame
- Q&A: Troubleshooting Bulldog Powered A-Frame Jack that Stopped Working
- Video: Ultimate Overview of the Square Direct Weld Jack
- Search Results: 500370
- Search Results: trailer hitch
- Search Results: ultra~fab products trailer jack
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Article: How to Measure for Trailer Hitch Drop
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
on Accessories and Parts
Hoss
2/20/2025
Hello, yes battery is full. All wires are good. I did test the jack today it seemed to work fine. The only thing I can think of, it's been really cold here the past week 5 degrees. I think the jack doesn't work well in the cold. The control board buttons were acting up hence the motor wasn't working right the other day. I'll co tines to test again tomorrow. If problem is present, I was sent a warranty claim email to send back for a replacement