Shorelandr SRV55TBB Trailer Brake Rotor or Wheel Stud Replacement

Question

Question:

I have a 2007 Shorelandr SRV55TBB. I am replacing the tires and when I took the lugs off, the studs were damaged. The disc brake hub is in pretty poor condition due to use in a saltwater environment, so I am wondering if I can replace the lug studs and if so, what that part number is, and if you carry a replacement hub assembly with the disc and lug studs installed.

asked by: Mike

0

Expert Reply:

I have no way of looking up which studs were used on your trailer, but if you can drive out one of the studs and provide the dimensions shown in the provided diagram, I'd be happy to recommend a replacement.

I did find a few specs online for your Shorelandr trailer, it looks like it uses tandem 3500 lb axles which would have an inner L68149 and an outer L44649 wheel bearing and a 5 on 4-1/2 inch wheel bolt pattern. If that's the case, you could use a # KHR10D replacement hub/rotor which uses 1/2 inch wheel studs.

expert reply by: Mike L

0

How to Measure for Replacement Wheel Stud
(click to enlarge)

Answer 1

I believe what you mentioned is a standard way of running trailer brake lines on a tandem trailer. I attached a diagram for the brake line kit part #18TA-BLKIT and how it normally connects to a trailer. The main feed line runs to the first axle where…

view full answer...

Answer 2

Let's start with the similarities. Both kits are compatible with L44649 and L68149 bearings and a 10-19 grease seal. Both kits are intended for use with a 3500 lb axle. Both are intended for marine applications and use dacromet rotor/hub…

view full answer...

Answer 3

I will start by saying that your TDE 11033L hub uses the #L68149 inner bearing and #L44649 outer bearing, which means you have a pretty standard #84 spindle on a 3,500 pound axle. With that said, we do not carry Tie Down Engendering products, so the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Shorelandr SRV55TBB Trailer Brake Rotor or Wheel Stud Replacement

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching