Replacement Bearing/Seals for Hubs With 1 Inch Spindle
Published 08/20/2021
Products Featured in This Question
Question:
I have a home made trailer with a 4 bolt hub. The axle has a 1inch diameter shaft. Diameter at the inside of seal is around 1.230 inches. Diameter of inside of hub for seal is around 1.985 inches. Outside bearing is a 44643 bearing. Inside Bearing is destroyed so no number there. I woudl liek a complete bearing a seal kit. Can you recommend a part number. Axle more than likely was original equipment on a Coleman Pop up camper. Thanks
asked by: Mark L
Expert Reply:
If the axle has a straight spindle with an L44643 outer bearing, it would use the same L44643 inner bearing.
So, we've got the bearings and their compatible L44610 races covered. For the grease seal, you're most likely needing a 34823 seal which has an ID of 1.249 inches and an OD of 1.983 inches which is super-close to the measurements you provided. The seal ID can be tricky to get because it's usually pretty mangled when it's removed.
The easiest way to get the seal ID is measure the surface of the spindle that the seal rides against. If that measurement proves to be right at 1.249, then you'd need the # BK1-100 bearing kit which includes the L44643 inner and outer bearing, the 34823 double lip grease seal and the L44610 races. A replacement cotter pin is also provided.
I've linked to an install video and some help articles that might come in handy.
Product Page this Question was Asked From
Bearing Kit for 1" BT8 Spindle, L44643 Inner/Outer Bearings, 34823 Seal
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- Bearing Kits
- Bearing L44643
- Race L44610
- 2000 lbs Axle
- 2500 lbs Axle
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: lubrimatic
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized
- Shop: Submersible, Under 80" Trailer Light Kit with 25' Wiring Harness
- Search Results: grease seal
- Shop: CE Smith Trailer Hub Assembly w/ Carrying Case for 2,500-lb Axles - 4 on 4 - Pre-Greased - Threaded
- Shop: Grease Seals 10-36 (pair)
- Search Results: seal cross reference
- Shop: Replacement Dust Caps for etrailer Bearing Protectors for 2.32" Hub Bore - Qty 2
- Shop: Grease Cap, 2.44" OD Drive In - Qty 2
- Shop: Double Lip Seal for 3,700-lb Marine Hubs
- Q&A: Availability of Replacement Grease Seal w/ 1.25 Inch Inside Diameter and 1.98 Inch Outside Diameter
- Q&A: Grease Seal Recommendation To Replace Seal with ID of 1.25 and Outer Diameter of 1.983
- Search Results: hubs for 1 inch spindle
- Search Results: ask a question
- Q&A: Replacement Hub for Old Boat Trailer with 07100 Bearing
- Q&A: Determining Which Replacement Bearing, Race, and Seal For Spindle Using 07100 Bearing
- Q&A: Does Trailer Wheel Bore Need to Match Exactly When Picking Out Replacement
- Video: 4" Carbon Fiber Digital Caliper Feature Review
- Video: An In-Depth Look at the CE Smith Trailer Hub Assembly w/ Carrying Case for 2,500-lb Axles
- Q&A: How to Measure a Trailer Hub or Dust Cap to Find the Right Replacement Dust Cap
- Q&A: Replacement Trailer Hub for Boat Trailer with Timken Bearings 07100