Yakima Replacement Tower Kit For Rack And Roll Bolt Size

Question

Question:

Will M8 Bolts Fit Through the Holes

asked by: Philip N

0

Expert Reply:

I spoke with Yakima, and they confirmed the M8 bolts will not fit the Tower Kit for Rack and Roll # 8880179. The bolts are actually a M10 1.5 x 25.

expert reply by: Bryce D

0

Answer 1

Hey Drew, thanks for reaching out! I'm not exactly sure which width dimension you're needing for the Replacement Tower Kit #8880179, but I went out to the warehouse and took some measurements which you can see in the attached photo. Let me…

view full answer...

Answer 2

I went out to our warehouse to take a look at the Yakima Replacement Tower Kit #8880179. I measured an overall height on the towers of right at 3-3/4 inches. The 4 T-bolts that are included feature an overall height of 1-1/8 inches and a thread…

view full answer...

Answer 3

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 4

The Replacement Spindle Washer #5-101 referenced in your question is designed for 1 inch, D type spindles. The washer will install right between the castle nut and outer bearing, and the tang on the washer is bent up to prevent the nut from turning.…

view full answer...

Answer 5

Hey Rick, thanks for the information! Your LUV2314LW-03 Shorelandr boat trailer has 2,995 lbs capacity. The Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 item #AKIHUB-545-35-EZ-K, you referenced will definitely fit your trailer.…

view full answer...

Answer 6

I reached out to CE Smith and found that they use Kendal grease on the CE Smith Trailer Hub Assembly #CE13511. The grease color they use is the red grease like #L11390, although they did say it is possible it may be tan but it is the same thing.

view full answer...

Answer 7

Hey Blake! Are those disc brakes or drum brakes? The Dexter DX7.5L A-60 Brake Actuator w Electric Lockout #DX56FR you were looking at is designed for disc brakes, fits a 3" x 5" tongue, and has a 2" coupler so it will fit a 2"…

view full answer...

Answer 8

Hey Jim, the best alternative to the mounting hardware you have now would be the current Yakima roof rack components that they list for installing the round bars on your 2015 Toyota Sienna which is their Timberline kit that consists of part numbers…

view full answer...

Answer 9

Hey Duane, Once the bearings are packed with grease and the hub is on the spindle you'll need to slowly pump grease into the spindle until you see it start to seep out of the outer bearing. Be sure to use a manual grease gun so the grease…

view full answer...

Answer 10

Unfortunately Curt, I do not see a date code in the image you sent in. The date code is going to be a 4 digit number with the first 2 numbers referencing the week of the year it was manufactured and the last 2 digits being the last 2 digits of the…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Yakima Replacement Tower Kit For Rack And Roll Bolt Size

Product Page this Question was Asked From

Continue Researching