Install Hardware for Brophy D-Rings LRB1

Question

Question:

I got the 1/2inch drings for my trailer what kinda bolts should I use to anchor them to a 2×pressure treated wood

asked by: Steven

0

Expert Reply:

According to the measurements we took the mounting holes on the Trailer D-Ring Tie Down, # LRB1, will accept bolts no larger than 7/16 inches in diameter so you could go with a 3/8 inch bolt/nut or screw. You can just use standard hardware which can be obtained from your local hardware store.

We do not offer any hardware for these tie downs so you would have to source it locally.

expert reply by: Jameson C

0

Answer 1

The Brophy Stake Pocket Tie Down Anchor item #TL2B is made in the USA. I have linked a review video below.

view full answer...

Answer 2

Hello David, thanks for reaching out. The difference between the Brophy Stake Pocket Tie Down Anchors #TL1B and #TL2B is the D-ring size. The #TL1B has a 2-5/16" D-ring, while the #TL2B has a 3" D-ring. I have included a drawing with the…

view full answer...

Answer 3

If the inner width of your flatbed trailer's stake pockets are 3-1/2" then you're going to want the Brophy Stake Pocket Tie Down Anchor item #TL2B you were looking at. The dimensions are 8-1/4" tall x 3-1/2" wide x 1-1/2"…

view full answer...

Answer 4

So I went out to the warehouse and measured the stake pocket anchor #TL2B and from the lip to the top of the pin hole is right at 6-3/4". As long as your stake pocket is really only 6" deep these will work just fine for you.

view full answer...

Answer 5

I have a solution for you, but it is not easy to weld steel to aluminum. The Curt D-Ring Tie Down Anchor #J-705 is made of raw steel. It will not work well to weld on to your aluminum trailer because of the differences in the melting points of these…

view full answer...

Answer 6

While we do have the perfect fitment for you, the Firestone Ride-Rite Rear Axle Springs #F2615 do not fit your 2014 Ram 3500 2wd cab and chassis. This is because the #F2615 is designed to fit only 4x4 pickup model trucks. With that being said, I…

view full answer...

Answer 7

I have an air bag solution for you. Unfortunately, if you have a 2022 Ram 3500 CA60 chassis cab, the Air Lift LoadLifter 7500 XL #AL57531 will not fit. This is because these air bags are only designed for standard pickup models. However, we do have…

view full answer...

Answer 8

Yes we have just the thing. For an air bag kit I recommend the Firestone Ride Rite #F2478. These are 4,800 lb capacity bags and will do a great job of keeping your truck level and increasing stability. We do have the wireless compressors as well. I…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Install Hardware for Brophy D-Rings LRB1

Product Page this Question was Asked From

Continue Researching