Replacement C-Jack 404488 For Lippert Electric Ground Control

Question

Question:

I have a Lippert Electric Ground Control unit P/N 404488 SN/ 11/17/20. Your replacement part shows a L/C 404488 SN/ 06/08/18. Is your replacement part two years older? Will is work with the newer unit?

asked by: Stanley C

0

Expert Reply:

As long as your C-Jack part number is 404488, then the Replacement C-Jack for Lippert Electric Ground Control TT # LC404488 will work for you. The pictured jack may have been from 2018 but it is the correct part number for your Lipper Electric Ground Control # LC672136.

expert reply by: Andrew N

0

Answer 1

We don't have any internal repair kits for the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System #LC358590 as they are not available but we do have replacement jack legs like the part #LC362485 which would replace the damaged leg…

view full answer...

Answer 2

We have the part number you are looking for with #LC404488 which gives you the replacement leg and motor you are looking for. Based on what you described experiencing this is the correct solution for your problem as well.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 9

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 10

Hey Doug. So long as your Husky 5th wheel hitch isn't three decades old you shouldn't have any issues attaching it to the B&W Custom Installation Kit w/ Base Rails item #BWRVK2402. Most 5th wheel hitches for the last 20 years have used…

view full answer...

Answer 11

Hey Kyle. Unless you're driving around with 1,500 lbs of gear in the bed of your 2025 Ford F-250, the Air Lift LoadLifter 5000 Ultimate Air Helper Springs item #AL29DQ are not going to be overloaded. Your 5th wheel hitch and a full tank of fuel…

view full answer...

Answer 12

Hey Ken! Instead of worrying about fitment and a potential return I can give you some measurements so you can figure it out before ordering. The standard shank on the B&W Continuum Weight Distribution System #BW28FR is 11-3/8" from the…

view full answer...

Replacement C-Jack 404488 For Lippert Electric Ground Control

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching