Solution for Damaged Front Jack Leg of Lippert Ground Control 3.0 Leveling System

Question

Question:

Does this work on a Lippert ground control 3.0 front jack

asked by: Brian T

0

Expert Reply:

We don't have any internal repair kits for the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System # LC358590 as they are not available but we do have replacement jack legs like the part # LC362485 which would replace the damaged leg you have now and get you back going!

expert reply by: Jameson C

0

Answer 1

As long as your C-Jack part number is 404488, then the Replacement C-Jack for Lippert Electric Ground Control TT #LC404488 will work for you. The pictured jack may have been from 2018 but it is the correct part number for your Lipper Electric Ground…

view full answer...

Answer 2

We have the part number you are looking for with #LC404488 which gives you the replacement leg and motor you are looking for. Based on what you described experiencing this is the correct solution for your problem as well.

view full answer...

Answer 3

Per the manufacturer when it comes to the shear pins being broken you would have to replace the whole Lippert Jack #LC298707 because the shear pins are not replaceable, and there is no way to fix them. What you will need to do is purchase a whole new…

view full answer...

Answer 4

Can you let me know what landing gear set you have on your RV? I don't have a way to look that up so I would need you to get me that info.

view full answer...

Answer 5

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 6

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

Hey Patrick, thanks for reaching out. Yes, the Replacement Front Jack Leg #LC362485 should work for your 2021 Open Range 314RLS with the Lippert Ground Control 3.0 system. Since your weld stop “bump outs” measure 17-1/2" apart, that matches the…

view full answer...

Answer 9

It sure is Wesley. The Replacement Front Jack item #LC362485 is exact what you will need for the 6 point Lippert Ground Control 3.0 Leveling System item #LC675817. The Replacement Front Jack item #LC362485 can be used as a replacement for either the…

view full answer...

Answer 10

Thanks for the information and picture James! Your Curt 5,100 lbs capacity axle uses item #25580 inner bearings and item #LM67048 outer bearings. So you would need the Bearing Kit item #BK3-300, which includes both bearings, along with both races, a…

view full answer...

Answer 11

The distance between the insides of the weld stops on the jack leg #LC362485 is 17-1/2 inches and the outer tube diameter is 2-1/2 inch by 2-1/2 inch.

view full answer...

Answer 12

Unfortunately, there is not Kenny. If your Replacement Front Jack for Lippert Ground Control 3.0 Leveling System item #LC362485 is damaged or not functioning correctly the only option available is to replace it. The Replacement Front Jack item…

view full answer...

Solution for Damaged Front Jack Leg of Lippert Ground Control 3.0 Leveling System

Product Page this Question was Asked From

Continue Researching