What Height Should Lippert Hydraulic Leveling or Ground Control Systems Be Installed From Ground

Question

Question:

How do I know witch mounting holes to use ,have toy hauler and my center jack looks low when up.can i unbolt and move up ? Do I need to adjust anything .Re level

asked by: Larry H

1

Helpful Expert Reply:

Typically with a Lippert Hydraulic Leveling System # LC36VR or Ground Control # LC675817 you'll get the most range when the jack foot is 7" from the ground, but you can adjust as necessary if you tend to run into clearance issues. You can adjust as necessary, but make sure that you're adjusting everything similarly so you don't run into gaps where legs can't extend far enough.

expert reply by: Erik B

1

Answer 1

Front hitches have different weight capacity listings so both numbers are correct. The Curt Hitch part #31038 does have a straight line pull rating of 9,000 lbs and a gross trailer capacity of 5,000 lbs. So if you have a rolling load on level ground…

view full answer...

Answer 2

We might have a solution, but I'd need to know what year 550 you have.

view full answer...

Answer 3

Hello Sal, Since you have the 1st Generation silver with 6 holes, you are going to want the Replacement Hydraulic Jack Assembly for Lippert Level Up 5th Wheel RV Leveling System - 14K - Gen 1 #LC25AF. You are probably thinking, "I said 6 holes,…

view full answer...

Answer 4

Hey James, we need to figure out what leveling system you have on your 2005 Holiday Rambler Ambassador 40 foot and determine if we have a replacement front jack for it. Is there any part number or brand info you can see on the jack leg? If you can…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

What Height Should Lippert Hydraulic Leveling or Ground Control Systems Be Installed From Ground

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching