Correct Replacement Hub For Jet Ski Trailer With BT150 Hub
Updated 07/29/2021 | Published 07/28/2021 >
Products Featured in This Question
Question:
Hello! I recently purchased a used jet ski trailer with a locked up hub. I pulled the hubs and measured the spindle to a circumference of 3 3/8 inches. Thats where I dead end! It has straight spindles but I cant seem to find any hubs with the same inner and outer bearings that fit this size spindle? The original hubs were stamped BT150, the trailer make is Hustler. Any help would be appreciated! Thanks
asked by: Kyle C
Expert Reply:
I would be happy to help!
Based on the BT150 stamped in your hub you will need the CE Smith Trailer Idler Hub Assembly # CE13315 which includes inner and outer bearings # L44649. This hub comes pre-greased and ready to install on the spindle of your Jet Skit Trailer making it a very easy option.
I included a video of the # CE13315 for you to take a look at.
Product Page this Question was Asked From
Dexter Trailer Idler Hub Assembly for 6,000-lb Axles - 6 on 5-1/2
- Trailer Hubs and Drums
- Idler Hub
- Standard
- 25580 / 15123
- Standard Grade
- For 6000 lbs Axles
- 1/2 Inch Stud
- 6 on 5-1/2 Inch
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- 17 Inch Wheel
- 17-1/2 Inch Wheel
- 18 Inch Wheel
- 18-1/2 Inch Wheel
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: CE Smith Trailer Idler Hub Assembly w/ Case for 2.7K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased
- Shop: CE Smith Spindle Nuts, Washers, and Cotter Pins for 1" Axle - Qty 2
- Shop: CE Smith Trailer Hub Assembly w/ Carrying Case for 2,700-lb Axles - 5 on 4-1/2 - Pre-Greased
- Article: How to Tell the Weight Rating of a Trailer Axle
- Search Results: bearing buddy trailer bearings races seals caps
- Shop: Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel - Qty 2
- Shop: Kenda 4.80-12 Bias Trailer Tire with 12" Galvanized Wheel - 5 on 4-1/2 - Load Range B
- Shop: Loadstar 4.80-12 Bias Trailer Tire with 12" Galvanized Wheel - 5 on 4-1/2 - Load Range C
- Q&A: Replacement Hub For an Older Shorelander Trailer With Inner Bearing 1-3/8 Inch & Outer 1-1/16 Inch
- Q&A: Replacement for Hub to Fit with Shorelander SS734 Bearing Kit
- Shop: Replacement Canister Drain Tubes for Retrax Hard Tonneau Covers - Qty 2
- Video: In-Depth Review of the CE Smith Trailer Idler Hub Assembly w/ Case for 2.7K Axles
- Video: CE Smith Trailer Hub Assembly w/ Carrying Case for 2,700-lb Axles Spec Review
- Q&A: What Is the Difference Between a BTR and BT8 Spindle
- Q&A: Should There Be a Washer on Trailer Spindle Between Spindle Nut and Outer Bearing
- Q&A: Recommended Hub w/ a 5 on 4-1/2" Bolt Pattern that Fits a BTR Spindle w/ L44649 Bearings
- Search Results: btr spindle
- Q&A: Replacement Trailer Hub for the TDE 46205 with Galvanized Finish
- Q&A: Can Knicked Spindle be Smoothed Out and Reused
- Video: The Low-Down on the Square BT8 Spindle for 2,000-lb Trailer Axles
- Search Results: trailer tires and wheels
- Shop: Trailer Hitch
- Article: How to Accurately Measure Trailer Leaf Springs
- Shop: Trailer Wiring
- Article: Double-Eye Trailer Suspension System Review
- Search Results: trailer jack
- Shop: Suspension Enhancement
- Search Results: trailer leaf springs
- Shop: Brake Controller
- Search Results: trailer hubs and drums


