How To Stop Scuffs On Hull Of Boat When Using CE Smith Multi Sport Boat and Kayak Trailer

Question

Question:

I have the CE Smith Multi Sport Boat and Kayak Trailer w/ Bunks - 8inch Wheels - 12foot Boat - 800 lbs. I love the trailer, but have found the roller or the bow stop are marring the finish on the small antique mahogany hulled dinghy. The bow is very rounded . Do you have any suggestions? The boat is very light 100 lbs but the hull is very curvaceous. - Different rollers? - Additional support for the hull? Any guidance is greatly appreciated.

asked by: Pat C

0

Expert Reply:

If you replace the bow roller with one that is non-marring then that should fix any issues with scuffs on the hull of the boat. For this, I recommend the Yates Bow Roller for Boat Trailers part # YR450Y for 4" wide or part # YR300Y for 3" wide.

expert reply by: Conner L

0

Answer 1

The CE Smith Multi Sport Plus Boat and Kayak Trailer #CE48870 uses #L44649 bearings. The correct Bearing Buddy Bearing Protectors are the #BB1980A-SS. These fit a 1.98" hub bore and L44649 outer bearings. They also have a stainless steel…

view full answer...

Answer 2

We have a really great option for a trailer for your 10 foot Bass Pro Pond Prowler boat, although the Malone trailer you mentioned has been discontinued by the manufacturer and is no longer available. Instead, which I highly recommend is an option…

view full answer...

Answer 3

Yeah, I can see that getting pretty obnoxious. I believe you are correct about the 4 Flat plug getting wet as the lights that come included with the CE Smith #CE48870 are fully submersible and all the connections are water proof. So with that said,…

view full answer...

Answer 4

The Fulton High-Performance 2-Speed Trailer Winch part #F142412 is the perfect replacement for a Shelby 5460A. It has a two speed operation just like your old winch and a bit higher capacity as well at 2,600 lbs compared to the 2,300 lb capacity of…

view full answer...

Answer 5

The Blue #YR1203SB and Yellow #YR1203SY Yates Keel Pads are the only keel pads we carry. While they do have some play you may consider trimming some of the side material on the pads which will allow it flex a bit more.

view full answer...

Answer 6

Wiring connections for the Electric Over Hydraulic Brake Actuator are as follows. Yellow - Cold side of breakaway switch, The wire that goes hot when a breakaway occurs. Black - Positive connection on breakaway switch, The wire that charges the…

view full answer...

Answer 7

Based on that part number it sounds like your bow roller is the Yates Keel Roller. We have two different options based on the diameter of your shaft. If you have a 5/8" shaft you need the #YR5213-5 and for a 1/2" shaft the #YR5213-4P. Both…

view full answer...

Answer 8

In regards to the Furrion Vision S Wireless RV Backup Camera System part #FOS43TASF, the male end is on the camera side and the female end is on the trailer side. If the trailer was pre-wired correctly for the Furrion Vision S Wireless RV Backup…

view full answer...

Answer 9

Yes, you can install the Voyager WiSight 2.0 Wireless Backup Camera System w/ Night Vision for Prewired RV #ASA24YR using the running light circuit as the activation circuit and you could easily flip on the tow vehicle running lights to see behind…

view full answer...

Answer 10

I have a few options that will work for you, but the Wesbar part number that you gave, 105826, is the part number of a discontinued wraparound lens for their discontinued wraparound trailer light 403078. Unfortunately these parts are no longer…

view full answer...

How To Stop Scuffs On Hull Of Boat When Using CE Smith Multi Sport Boat and Kayak Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching