Should You Completely Cover Wood on Bunk Boards with Marine-Grade Carpeting or Leave Wood Exposed

Question

Question:

Is it best to leave some wood exposed to help dry the boards or use the 18 inch wide and cover all the exposed wood? Thanks,

asked by: Ashby J

0

Expert Reply:

It is recommended to cover all of the exposed wood. When the wood is exposed there is a greater risk of rot and damage. The carpeting is made of breathable polyester which makes sure it can dry out so no mold will build up and damage the wood or carpet.

I have attached a video review for your reference.

expert reply by: Robin H

0

Answer 1

Hey Brian, welcome back! Yes the Kenda Karrier KR35 ST185/80R13 LRC Radial Trailer Tire w/ 13" Black AM09 Wheel #KE39TJ that you referenced is pre-mounted but it is not balanced. Generally speaking people don't balance trailer tires as it…

view full answer...

Answer 2

Hey Darrell, thanks for your questions and business! The Kenda Karrier KR35 ST185/80R13 Radial Trailer Tire w/ 13" Black Wheel - 5 on 4-1/2 #KE54TJ, like most trailer wheels, just requires that the lug nut is at least flush with the end of the…

view full answer...

Answer 3

Hey David, thanks for reaching out! What you described is definitely no bueno. The race is supposed to fit really snug in the hub assembly and then that's what makes contact with the bearings. You can technically spin the race inside the hub but…

view full answer...

Answer 4

The order of assembly is as follows (from the inside out). First, put the inner race in the back side of the hub, followed by the inner bearing, and then the seal. Insert the hub onto the spindle. Then, insert the outer race, followed by the outer…

view full answer...

Answer 5

Yes the bearing kit part #DL21792 is the correct kit for your trailer hub BT-100. This comes with two bearings L44643 like we know fit that hub part number.

view full answer...

Answer 6

There really should be a flat washer between the outer bearing of your hub and the nut that holds it on. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. The Washer For 1 inch Spindle,…

view full answer...

Answer 7

If you had to go without a washer, it wouldn't be the end of the world. The washer is intended to place even pressure against the outer bearing, but if you draw down the castle nut properly, you can get by without a washer, but I'd try to…

view full answer...

Answer 8

A bearing race or cone should fit tightly enough in the hub that it needs to be driven out of the hub with a punch from the back side. If the race is spinning in the hub, either the wrong race was used or the hub bore has been damaged in some way. If…

view full answer...

Answer 9

What concerns me about this situation is the scarring on the spindle. Depending on how deep and how bad the scarring is, a new set of bearings and a new hub/drum assembly might experience the same problem down the road. This would mean that the…

view full answer...

Answer 10

The Easy Grease Trailer Idler Hub Assembly #AKIHUB-440-2-EZ-1K will replace your current BT-100 idler hub. This hub fits your 1" straight Spindle #TRU59FR with the 4.80-8 Wheel and Tire #AM30040 and will use the Bearing Kit #BK1-100.

view full answer...

Answer 11

That is an excellent question! In some instances mixing regular grease like part #L11390 won't hurt when mixed with marine grease, but in some situations it can ruin your hubs/spindles and taking the extra time to clean off the grease and redo…

view full answer...

Answer 12

Yes, you'll want to replace the grease seals when packing the bearings but the grease cap can be reused if it's still in good condition. If you don't know what bearings and seals you need, I have a few options for you to help with…

view full answer...

Should You Completely Cover Wood on Bunk Boards with Marine-Grade Carpeting or Leave Wood Exposed

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching