Is There Socket that Would Fit in Place of End of Replacement Manual Crank Handle

Question

Question:

Is there a socket that I can put in a drill to use as a replacement for this wrench

asked by: Jerry J

0

Expert Reply:

The end of the Replacement Manual Crank Handle # LC119226 is a slotted cylinder which means there isn't a socket that would work as a substitute.

expert reply by: Jameson C

0

Answer 1

Thanks for reaching out Chris, I'd be happy to help. The Lippert Road Armor Equalizer Kit #LC53CK includes the two equalizers with the bronze bushings pre-installed. To complete the setup, shakles/wet bolts are in the Dexter Heavy-Duty Suspension…

view full answer...

Answer 2

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 3

We have just what you need to replace your landing gear motor M9000PK with the #LC196308 and you'd be set! This is a confirmed fit for what you have and is a faster motor too so your jacks will raise and lower quicker.

view full answer...

Answer 4

There are a few things to look at that could be your issue. Since your batteries are fully charged, I would suggest looking at it piece by piece. To get you proper parts, I need to know the manufacturer of the landing gear and any info about the…

view full answer...

Answer 5

Any powered landing gear or powered tongue jack will draw less power as it legs descend down toward the ground and much more as soon as they make contact and encounter resistance. This is a normal occurrence. In the same way, any jack - even a manual…

view full answer...

Answer 6

Hey Oakley, this is a great question and one that I've not had before. But yes you can use a hub/drum in place of an idler for a spare setup if needed. The hub/drums and the idler hubs are dimensionally the exact same in terms of the hub portion…

view full answer...

Answer 7

We can get you un-stranded! The correct follow leg for your landing gear is going to depend on how long it is. If your leg measures 29-1/2" (see attached photo), you would need replacement #LG-179014, which can be used with most landing gear…

view full answer...

Answer 8

If you are seeing your Atwood gear box moving around on the shaft of your landing gear that is because one of the tabs that holds it in place has sheered off. We see this problem on occasion and the only solution is to replace the gear box. What I…

view full answer...

Answer 9

The correct replacement for a Venture M-9000 PK Landing Gear Motor is the Lippert Venture 5th Wheel RV Landing Gear Motor part #LC142178 or you can upgrade to the Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor part #LC196308 which has a…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Is There Socket that Would Fit in Place of End of Replacement Manual Crank Handle

Product Page this Question was Asked From

Continue Researching