Replacement Bar Setup to Install Hullavator on Different Vehicle

Question

Question:

I am looking to add another hullavator to my existing bar for my girlfriend who already owns a hullavator for her car. Wondering if this part includes the necessary hardware to fasten it to my existing bar. This way all I have to do is move her hullavator assembly to my car. thanks

asked by: Gary D

0

Expert Reply:

If you wanted a to put a second mounting bar of a Thule Hullavator part # TH898 you'd need the bar part # 7521741001 that you referenced as well as the hardware bag part # TH88JV as well.

expert reply by: Jameson C

0

Answer 1

The Thule Hullavator Pro Kayak Roof Rack #TH898 will either clamp around the Thule WingBar Evo Crossbars #TH711420 or can be held inside the channel. The Bar Mount Assembly #7521741001 included with the carrier allows for either style attachment to…

view full answer...

Answer 2

The #BP19-001 retaining clips are designed to fit the Dexter 7-inch brake magnets. Our contact at Dexter said the BP19-001 will work on both the 7-inch round and the 10-inch oval magnets. The replacement magnet clip, part #BP19005 will fit 10, 12,…

view full answer...

Answer 3

You are correct that to install the Curt trailer wiring harness #C44ER on your 2021 Nissan Rogue you do not have to take the interior trim completely out. I did see the review from James where he said he didn't have enough wire which is confusing…

view full answer...

Answer 4

Hey Mark, I spoke with Thule and found that the Pro bar mount assembly #7521741001 would not be a fit, but we do still offer the original Hullavator bar mount assembly with part #TH753352403.

view full answer...

Answer 5

The Yakima HD Crossbars #Y01156 will work with the Thule Hullavator #TH898. Based on the pictures you sent in it looks like you have the crossbars installed upside down. The end caps have an opening on the other side that lets you easily slide in…

view full answer...

Answer 6

Your older style Thule Hullavator is designed to fit Thule Aeroblade bars but it mounts to them in the channels that are on top of the bars and not by wrapping around them. The bolts needed are part #919061654 which then thread to the square nut…

view full answer...

Answer 7

Only the latest version of the Thule Hullavator part #TH898 is compatible with aero shaped crossbars. So your options at this point would be the new Hullavators and an aero shaped roof rack like you want (expensive I know...), or a square bar roof…

view full answer...

Answer 8

I pulled a Replacement Square Nut #853-7557 from our warehouse and found that its dimensions were .79 by .79 of an inch and .17 of an inch thick. Check out the video I took that shows these dimensions.

view full answer...

Answer 9

The Replacement Square Nut #853-7557 is sold individually.

view full answer...

Answer 10

Yes, the Thule Hullavator Pro Kayak Carrier part #TH898 will work with the Thule WingBar Evo Crossbars. These are just an updated version of the Thule AeroBlade Crossbars. The Hullavator can be attached to the WingBar in one of two ways, with…

view full answer...

Answer 11

The Thule Hullavator Pro Kayak Carrier #TH898 has the ability to mount in crossbar channels, but it doesn't come with T-bolts. What you do is use the included hardware which allows you to do so, and you can see this starting on page 7 of the…

view full answer...

Answer 12

The Thule WingBar Evo crossbars do not require you to cut the rubber inside the channel at all; the rubber simply separates when you push into the channel so you don't have to worry about that. You can install the Thule Hullavator #TH898 by using…

view full answer...

Replacement Bar Setup to Install Hullavator on Different Vehicle

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching