Do You Have a Weld On # 84 Spindle With a Grease Zerk For E-Z Lube Hubs?

Question

Question:

Is it also available with the ez lube grease zerk?

asked by: Efrain L

0

Expert Reply:

The #84 E-Z Lube Spindle # TRU74FR matches the dimensions of the #84 Spindle # TRU64FR and will have the E-Z lube spindle and a brake flange. With the brake flange the stub will be 3/4" longer.

If necessary you can cut off the brake flange to get the correct length but otherwise it will not affect the operation of a non braking idler hub.

expert reply by: Bud M

0

Answer 1

I have three spindles that are for a 3,500-lb axle and have the bearing dimensions you have listed. The only difference is the dimension for the grease seal is 1.75 inches, not the 1.795 inches that you have mentioned. Maybe you typed in the seal…

view full answer...

Answer 2

Yes, you are going to want a spindle that has the 1.063" and 1.378" measurements. This is commonly known as a #84 spindle and can be found on our site with a few variances. For example, the TruRyde EZ Lube Spindle #TRU74FR comes with a…

view full answer...

Answer 3

No, they're welded. You assumed correctly. The spindles listed below that I referenced in your previous question all have to be welded on. There are no thread on spindles. #84 Spindle for 3,500-lb Trailer Axles - 2" Diameter item #TRU24FR…

view full answer...

Answer 4

A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Do You Have a Weld On # 84 Spindle With a Grease Zerk For E-Z Lube Hubs?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching