Will Curt Trailer Hitch Receiver C73DR Work W/ Lift Gate Sensor On 2021 Lexus RX 350
Updated 06/21/2024 | Published 05/06/2021
Products Featured in This Question
Question:
Is this hitch compatible with a Lexus RX 350 2021 with a rear trunk kick sensor? Thanks
asked by: Tom
Expert Reply:
The Curt Trailer Hitch Receiver # C73DR you were looking at is a confirmed fit for your 2021 Lexus RX 350 and will fit with your rear lift gate sensor though it will likely change the location your foot must be to activate the sensor.
You will need to place your foot to the left or right of the receiver for the sensor to detect your foot.
If you are planning on towing with your RX 350 you will also need a vehicle wiring harness # C56217.
I included videos of the products mentioned for you to take a look at.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 525 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 525 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: Beginner’s Guide to Installing the Curt Trailer Hitch Receiver on a 2024 Chevrolet Trax
- Q&A: Trailer Hitch that Fits 2021 Lexus RX 350
- Video: Installing the Curt Trailer Hitch Receiver on a 2022 Lexus RX 350
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Thule Apex XT Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches - Tilting
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Search Results: 13466
- Q&A: Bumper Panel Modification Required for Trailer Hitch Receiver On a 2021 Lexus RX 350
- Shop: Trunk Bike Rack
- Video: Mount: Curt T-Connector Vehicle Wiring Harness for Factory Tow Package on a 2021 Lexus RX 350
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Video: Set up: Curt Trailer Hitch Receiver on a 2022 Ford Escape
- Video: How to Install: Curt Trailer Hitch Receiver on your 2016 Honda CR-V
- Video: Installing the Curt Trailer Hitch Receiver on your 2014 Honda CR-V
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2019 Toyota Highlander C56217
- Q&A: Recommended 2 Inch Hitch for a 2021 Lexus RX 450h
- Shop: Roof Rack
- Q&A: Where is the Trailer Fuse on a 2021 Lexus RX 350?
- Q&A: Trailer Hitch Receivers Which Fit a 2020 Lexus RX 350 F Sport
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer wiring
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
on Trailer Hitch
Jerry S.
6/20/2024
I have purchased the Curt Trailer Hitch receiver #C73DR. I am going to install it on my 2022 Lexus RX 350 with the rear hatch kick sensor. I am unsure of how to protect/remove the sensor while I am cutting the notch in the facia for the receiving tube clearance. Can you send me pictures and give me an explanation of how to do this. I have seen the pictures of the sensor where they talk about removing two clips, but on my car it appears to be a panel which runs along the inside of the facia and I don't know if I can remove it or simply pry it up off the facia while cutting the notch. Help!