Are There Air Bags for a 1997 Ford F-350 with In-Bed Hitch

Question

Question:

Looking for a set of airbags for my 97 f350 that won’t interfere with my BandW turn over ball

asked by: John F

0

Expert Reply:

I do have suspension enhancement options for a 1997 Ford F-350 but air bags won't be one of them as they all mount in the same spot as the in-bed hitch. That said, the Timbren Rear Suspension Enhancement System part # TFR350SDE will work with an in-bed hitch and they provide more support than air bags. They also require zero maintenance.

expert reply by: Conner L

0

Answer 1

If the 5th wheel hitch install kit brackets that attach to the frame are the universal L-brackets (two per side) then it is possible to use Air Lift air bags #AL88215 on a 1994 Ford F-250/F-350. But it is still possible for there to be interference…

view full answer...

Answer 2

Hey Bill, The Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box #GY48GR has an 18.08" measurement from the center of the coupler to the center of the first bolt holes. When switching to a gooseneck pin box from the Lippert Turning Point…

view full answer...

Answer 3

Unless you'd be interested in going to a different suspension enhancement setup we won't have a solution since all of the gooseneck hitches we offer mount on the outside of the frame rails where your current air bag brackets are. The B and W…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 12

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Are There Air Bags for a 1997 Ford F-350 with In-Bed Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching