Roadmaster Direct-Connect Base Plate Kit Bolt Torque Requirements

Question

Question:

What is the torque value for long bolt on 2021 ram base plate install

asked by: Mike M

0

Expert Reply:

Please see the attached chart for all bolt torque requirements on the Roadmaster Direct-Connect Base Plate Kit with removable arms, # RM-522203-5, for your 2020 Ram 1500.

Note the attached link to installation video.

expert reply by: Michael R

0

Torque Value
(click to enlarge)

Answer 1

Yes, you would just wire the green and yellow stop/turn brake circuits from the Roadmaster Universal Hy-Power Diode Wiring Kit #RM-154 to your brake lights on your 2004 Jeep Grand Cherokee. If you want to utilize your amber turn signals on your Jeep…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

Thanks for the information Kevin! To flat tow your 2025 Ford Bronco with a standard bumper and LED lights, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect item #e84ZR Base…

view full answer...

Answer 12

Hey Lucian! There are definitely a lot of options out there, and the best is usually a mix of parts from different manufacturers. We don't have a package under a single part number but I can give you a list of parts for a complete setup. I…

view full answer...

Roadmaster Direct-Connect Base Plate Kit Bolt Torque Requirements

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching