What Are the Dimensions of the RC Manufacturing A-Frame Tool Box Lock Replacement

Question

Question:

Measurements overall

asked by: James

0

Expert Reply:

The overall dimensions of the # 3W-461-545-SSL-EP is 3-3/8" wide by 4-3/8" tall. The mounting holes at the top are 2-13/16" apart (green), the holes from top to bottom are 2-15/16" apart (blue line) and the bottom holes are 1-7/8" apart (yellow).

expert reply by: Erik B

0

dimensions
(click to enlarge)

Answer 1

Thanks for your question, Bhavin. I couldn't find anything definitive so I reached out to Yakima to get confirmation. They let me know that the Yakima SmarT-Slot Mounting Kit part #Y25AV will not work on the older SkyBox's. The only…

view full answer...

Answer 2

We do carry the replacement latch for the RC Manufacturing T-Series Trailer Tongue Toolbox #350980 that you referenced. It is listed as part #3W-461-545-SSL-EP on our site. This has the latch, seal, rivets, and new keys.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hey George, congrats on the new truck! You are definitely going to need to support the axle when lifting your Silverado with the Pacbrake Alpha HD Pro Air Bag Suspension Kit item #PB25RV. Lifting your truck by the frame will stretch the bags too far…

view full answer...

Answer 12

Hi Richard! From the top of the shank to the lowest part where the tri-ball sits on the #BWTS20067BMP is 11.125". If you have the balls at max drop with the tallest one hanging down that would be 12.5". We recommend at least 11" of…

view full answer...

What Are the Dimensions of the RC Manufacturing A-Frame Tool Box Lock Replacement

Product Page this Question was Asked From

Continue Researching