Replacement Latch Needed for the RC Manufacturing T-Series Trailer Tongue Toolbox # 350980

Question

Question:

I have this box and can’t not find parts for paddle lock hinge. Second time broke and have to tie down lid. Very disappointed and desire a fix but I need hinge assy that attacts to lid. No luck to date

asked by: Doug S

0

Expert Reply:

We do carry the replacement latch for the RC Manufacturing T-Series Trailer Tongue Toolbox # 350980 that you referenced. It is listed as part # 3W-461-545-SSL-EP on our site.

This has the latch, seal, rivets, and new keys.

expert reply by: Jon G

0

Answer 1

The overall dimensions of the #3W-461-545-SSL-EP is 3-3/8" wide by 4-3/8" tall. The mounting holes at the top are 2-13/16" apart (green), the holes from top to bottom are 2-15/16" apart (blue line) and the bottom holes are…

view full answer...

Answer 2

One latch. The Replacement Handle Latch and Key for RC Manufacturing A-Frame Trailer Tongue Tool Boxes item #3W-461-545-SSL-EP is sold individually.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 11

Hey Micah! Pacbrake has actually been around for a long time, more than 60 years. We have had customers ask for these air bags in the past, and we've seen them on vehicles coming in. Until now, Firestone has been the go to since their quality is…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Replacement Latch Needed for the RC Manufacturing T-Series Trailer Tongue Toolbox # 350980

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching