Will the Tuson Towable Tire Pressure Monitoring System Interfere with Factory TPMS

Question

Question:

Any chance of signal interference with the factory installed sensors on my tow vehicle?

asked by: Neil F

0

Expert Reply:

The Tuson Towable Tire Pressure Monitoring System part # 335TPMS4WIVS will not interfere with factory installed TPMS.

expert reply by: Conner L

0

Answer 1

Hey Milos, I would go with the ball sensor setup part #TUS37FR over the part #335TPMS4WIVS since it is totally separate from the tires valve stems. So if you were to happen to have a valve stem issue and you had the ball sensor kit you could use…

view full answer...

Answer 2

The Tuson Towable Tire Pressure Monitoring System #335TPMS4WIVS updates the tire pressure, tire temperature, and vehicle battery voltage on the monitor every 5 seconds.

view full answer...

Answer 3

The batteries in the sensors of the Tuson Towable Tire Pressure Monitoring System #335TPMS4WIVS that you mentioned will last around 5 years with normal use and are not replaceable. You'd have to replace the sensor with the part #335TPMS-SENS…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Will the Tuson Towable Tire Pressure Monitoring System Interfere with Factory TPMS

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching