Replacement Spindle Compatible with Tie Down Engineering 46210 Hubs

Question

Question:

What size spindle do I have if I have tie down engineering 46210 hubs? Looking for a replacement.

asked by: Nicholas B

0

Expert Reply:

You have a standard 3500 lb axle, which uses a # 84 spindle compatible with a L68149 inner and an L44649 outer bearing.

We offer a few replacement # 84 spindles with different stub diameters.

• For an E-Z lube spindle with a brake flange and a 1-3/4 inch diameter stub, use # TRU74FR
• For a standard spindle without the brake flange and a 2 inch diameter stub, use # TRU24FR

expert reply by: Mike L

0

Answer 1

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 10

The Easy Grease Trailer Idler Hub Assembly for 3.5K Axles part #AKIHUB-545-35-G-EZ-K is a direct replacement for a UFP H-1377.

view full answer...

Answer 11

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Answer 12

Hey George! I do have brakes made specifically for your Demco KK260 Kar Kaddy! Demco Hydraulic Drum Brake - Single Servo - Galvanized - 10" - LH - Self-Adjusting - 3,500 lbs #DMSB24429M and Demco Hydraulic Drum Brake - Single Servo - Galvanized…

view full answer...

Replacement Spindle Compatible with Tie Down Engineering 46210 Hubs

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching