Will MaxxFan Deluxe Roof Vent Keep Fan Setting & Can it be Used With Wall Switch

Question

Question:

Id like to hook this up to a wall switch in the bathroom, but I see that it has push button controls. If I turn the power off at the wall switch with the fan on speed setting 2, will it go back to that setting when power is reapplied at the switch or will the on button for the fan need to be pressed each time?

asked by: Aaron C

0

Expert Reply:

The fan setting you are using will remain after turning off the MaxxFan Deluxe Roof Vent with 12V Fan # MA00-05301K, but that is only with the key pad controls on the actual fan. It isn't recommended to use a wall switch with this fan though as it is designed to have constant 12 volts and there could be issues with the circuit board; it hasn't been tested with a switch to know if the fan setting will remain but it is unlikely without having constant power.

If you do want to use a 12 volt fan that can be operated with a wall switch or even a remote there are other options I recommend over the MaxxFan Deluxe Roof Vent with 12V Fan # MA00-05301K.

For a powered vent that includes a wall switch the best option is from Ventline, the Ventline Ventadome Roof Vent with 12V Fan and Wall Switch - Smoke # V2119-3-533 or White # V2119-1-533.

Or you could go with an upgraded unit with a remote, the MaxxFan Deluxe Roof Vent w/ 12V Fan, Thermostat, and Remote - Powered Lift - 10 Speed # MA00-07500K.

I have added links below to each of these vents for you to check out as well.

expert reply by: Kyle S

0

Answer 1

Hey Bryan! I definitely understand not wanting to pull a hub to find the right seal size. It's not the most fun (nor cleanest) job in the world. Without actually doing that and verifying the right size, I can give you an answer that's about…

view full answer...

Answer 2

The Replacement Handheld Remote for MaxxAir Roof Vent Intake/Exhaust Fans #MA00A01150K and the Replacement Remote for MaxxAir Roof Vent Exhaust Only Fans #MA00A01151K is not the same part, and will fit different models. If you have the MaxxFan Deluxe…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Will MaxxFan Deluxe Roof Vent Keep Fan Setting & Can it be Used With Wall Switch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching