Will the Universal Mounting Panel For Redarc Tow-Pro Fit a Contura Switch Panel

Question

Question:

EBRH-ACCV3 REDARC The install instructions show a universal switch panel part #8 on kit contents Is that switch panel inset sized properly for a contura switch panel? Contura opening is 1.450” x 0.830”. Trying to figure out my switch layout prior to purchasing components

asked by: Peter H

0

Expert Reply:

The Universal Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob # 331-TPSI-001 is 1-1/16" wide x 1.5" tall, so it will fit on that Contura switch panel. Keep in mind that the housing is going to sit on the outer border of the panel, so you'll want to make sure that anything mounted next to it has sufficient clearance. This mounting panel comes included with the Redarc Tow-Pro Elite # RED44FR brake controller.

I've also linked a review video that we did where these measurements are detailed.

expert reply by: Erik B

0

Dimensions
(click to enlarge)

Answer 1

Hey John, congrats on the new truck! We can absolutely provide all the parts you need to flat tow your 2026 GMC Canyon AT4. We have the rebuild kit for the Falcon 2 tow bar as well. Here is what I recommend: - Roadmaster Direct-Connect Base Plate Kit…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Thanks for the information Kevin! To flat tow your 2025 Ford Bronco with a standard bumper and LED lights, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect item #e84ZR Base…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 11

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 12

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Will the Universal Mounting Panel For Redarc Tow-Pro Fit a Contura Switch Panel

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching