BK LED on Curt 7-Way Adapter, Part # C57674, Remains Lit Even Without a Trailer Connected
Updated 11/17/2024 | Published 02/06/2013
Question:
I have a brake controller installed. Is this light supposed to remain lit? Even with no trailer connected? Thank you,
asked by: Aaron
Expert Reply:
If you do not have a proportional brake controller (but instead have a time-delay type) the LED being lit could indicate a short to the controller output circuit. In some cases the manual brake switch on your controller may be partly engaged; this would also cause a signal to be sent to the 7-way BK LED. You can correct this by flipping the manual switch on and off several times to clean the contacts.
If you are using a proportional type brake controller such as the Prodigy P2, part # 90885, there will always be a very small voltage from the controller sent to the 7-way connector. This is because the controller is always checking to see if a trailer is connected.
The current draw from an LED is quite small (a tiny fraction of an amp) so this does not pose any concerns for battery drain. Your Curt 7-way is supposed to function in this manner.
Product Page this Question was Asked From
Adapter 4 Pole to 7 Pole and 4 Pole w/Test Lamps
- Custom Fit Vehicle Wiring
- Wiring Adapters
- Universal Fit
- 4 Flat to 4 Flat
- 4 Flat to 7 Blade
- Plug and Lead
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In
- Shop: Trailer Wiring
- Shop: Adapter 4 Pole to 7 Pole and 4 Pole w/Test Lamps
- Shop: Curt Trailer Connector Adapter - 4-Way to 7-Way RV and 4-Way Flat
- Q&A: Should the 12 Volt Circuit On the Adapter 4 Pole to 7 Pole with Test Lamps Stay On All the Time
- Q&A: Should the BK Indicator Light on the Curt Adapter be Lit up While Vehicle is Off and No Trailer
- Q&A: 12 Volt Warning Lights Stays on After Install 4 to 7-Way Converter on a 2006 Nissan Pathfinder
- Q&A: Installing a 7-Way Trailer Connector on a 2017 Subaru Outback Wagon
- Shop: Trailer Hitch
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer wiring
- Video: How to Choose a Trailer Brake Controller
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: trailer tires and wheels
- Shop: Suspension Enhancement
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer jack
- Shop: Brake Controller
- Video: Feature Breakdown: Universal Installation Kit for Trailer Brake Controller
- Article: How to Measure for Trailer Hitch Drop
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Gooseneck Hitch
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional
on Custom Fit Vehicle Wiring
Adam
11/17/2024
Hello, I have the Tekonsha P3 and the trailer test led is causing a false reading that my trailer plug is plugged in when in fact it is not. My P3 controller sends out a pulse to check for the trailer being plugged in and the led lights up for a secound and is causing a small resistance load making my unit think the trailer plug is connected. I feel this is a safty concern because if my trailer plug comes out i will never know that it is disconnected. Any solutions would be appreciated, I thought about taking the led out of circuit because i don't need that feature being my P3 unit will tell me if my trailer plug is not plugged in. Thank you Ed