Availability of U-Bolts of CE Smith Guide Ons # CE27670

Question

Question:

I believe you misunderstood the Question Its about the availability of the brackets - not the U-bolts or the KIT

asked by: Steve P

0

Expert Reply:

For just the U-bolts of the # CE27670 we have the part # CES44FR.

expert reply by: Jameson C

0

Steve P.

2/11/2021

I believe you misunderstood the Question Its about the availability of the brackets - not the U-bolts or the KIT

Jameson C.

2/11/2021

For the uprights you'd want the part # CE27608PG.

Answer 1

When installing rubber rollers like a keel or bow roller there are a couple of parts in addition to the roller you usually need. First, the roller needs to mount to a bracket of some kind. For example, if you are using a 5/8 inch steel shaft you…

view full answer...

Answer 2

We do have some of the replacement rollers that will work for your vintage 1965 boat trailer, but we do not have some of the rollers you asked about. Thank you for the dimensions. For the very front keel roller I recommend part #YR5213-5. This…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Availability of U-Bolts of CE Smith Guide Ons # CE27670

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching