Easy Brake Controller Solution for 2018 Acura MDX without Trailer Wiring

Question

Question:

need help. I am looking at wiring up my 2018 mdx awd and need to know if i have what I need. I wanted the redarc tow pro elite brake controller and the t one harness in the back for 7 way 118289 I wanted to know does this setup mean i do not need to run wires from the front to the back of the car? I am trying to keep from making that run if possible. The car is a 2018 mdx tech package awd.

asked by: Rick A

0

Expert Reply:

I have a solution that would allow you to install a brake controller in your 2018 Acura MDX without factory wiring. You'll need the Redarc Tow Pro Elite part # RED44FR that you mentioned with the install harness # 3028-P and then the 7-way kit part # 118289 and you'd be set.

All of the brake controller wiring is present on the versions of your vehicle with or without the tow package.

expert reply by: Jameson C

0

Answer 1

Yes, it can and that is exactly what you need! The Curt T-Connector Vehicle Wiring Harness item #CU86FR is custom fit for your 2017 Honda Pilot. It will provide you with a 7-way connector so you can tow a trailer with brakes. Some other parts you…

view full answer...

Answer 2

To tow a lightweight trailer with the 2020 Honda Pilot you will need a hitch, wiring, pin, ball mount and ball. For the hitch I recommend, etrailer Trailer Hitch Receive part #e98840 which has a nice matte finish that does not show scratches as…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Easy Brake Controller Solution for 2018 Acura MDX without Trailer Wiring

Products Featured in This Question

Continue Researching