Westin Replacement LED Light Kit for Westin Running Boards

Question

Question:

Do these lights fit this model of running board Code: 27-9904?

asked by: Gil R

0

Expert Reply:

The Westin LED Light Kit, # 27-6000, is designed for use with the Westin Sure-Grip running boards. Part # 27-9904 that you mentioned is a set of replacement lenses and housings for molded, lighted running boards. The molded running boards are not the same as the Sure-Grip running boards so the LED light kit will not fit the molded running boards.

For replacement bulbs for the molded, lighted boards use # 27-9905 and for replacement wiring harness use # 27-9903.

expert reply by: Michael H

0

Gil

1/28/2013

Is a LED replacement lights available for the Part 27-9904 type running boards?

Patrick B.

2/8/2013

All we carry as direct replacements for the Westin Molded, Lighted running boards are the incandescent kits, part 27-9905. Westin does not have an LED alternative. I called my contact to see if they knew what the bulb type was, and he said he thought it might be an H3, but was not sure. If you can positively identify the bulb type, it might be possible to find LED alternatives. If they are in fact H3 halogen bulbs, you will probably have a difficult time finding LED alternatives, but if your main concern is changing the color of the light, there are different H3 bulbs available. We carry a variety of H3 bulbs in different light color temperatures.

Answer 1

The molded panel on the 2012 Toyota 4Runner is standard with the trim package of the Limited 4Runner. The boards available that fit the Limited will fit below that panel in your photos. I recommend to use the Westin Sure-Grip Running Boards w/ Custom…

view full answer...

Answer 2

I took a look at what we have for the Westin Molded, Lighted Running Boards #27-0015, and the Replacement Lenses and Housings for Westin Molded, Lighted Running Boards #27-9904 actually comes with a rubber seal pre-installed so there is not a rubber…

view full answer...

Answer 3

Like the Custer Rubber Grommet #G65G, all the oval grommets we currently carry will be designed to fit a 6-1/2" light, like the Optronics LED Trailer Tail Light #STL72RB. However, we do have the Replacement Lenses and Housings #27-9904,…

view full answer...

Answer 4

We do have lenses for your Westin Molded, Lighted Running Boards #27-0015-1815. What you need are the Replacement Lenses and Housings for Westin Molded, Lighted Running Boards #27-9904.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Thanks for the information Calvin and welcome back! To add running boards to your 2018 Ford Explorer XLT, I recommend the Westin Sure-Grip item #27-6125-1965. They include a custom mounting kit that does not require drilling. The Westin Sure-Grip…

view full answer...

Answer 12

You can determine if you have a tow package by reaching out to a Ford dealer or by checking the undercarriage of Explorer. If it does have the tow package there will be a trailer hitch receiver and either a 4-pole or 7-way wiring harness visible as…

view full answer...

Westin Replacement LED Light Kit for Westin Running Boards

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching