Availability of Replacement Lenses for Westin Molded, Lighted Running Boards

Question

Question:

Are replacement lenses available for Westin Molded, Lighted Running Boards w/ Custom Installation Kit - 6 Wide - Black Item 27-0015-1815 Thanks

asked by: Derwyn W

0

Expert Reply:

We do have lenses for your Westin Molded, Lighted Running Boards # 27-0015-1815. What you need are the Replacement Lenses and Housings for Westin Molded, Lighted Running Boards # 27-9904.

expert reply by: Robin H

0

Answer 1

Like the Custer Rubber Grommet #G65G, all the oval grommets we currently carry will be designed to fit a 6-1/2" light, like the Optronics LED Trailer Tail Light #STL72RB. However, we do have the Replacement Lenses and Housings #27-9904,…

view full answer...

Answer 2

The Westin LED Light Kit, #27-6000, is designed for use with the Westin Sure-Grip running boards. Part #27-9904 that you mentioned is a set of replacement lenses and housings for molded, lighted running boards. The molded running boards are not the…

view full answer...

Answer 3

If you look at the attached photo you will see the integrated rubber seal. If that is what you are asking about then it does come with it. If you are looking for a different rubber seal then it will not. The Replacement Light Housings for Westin…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Availability of Replacement Lenses for Westin Molded, Lighted Running Boards

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching