Recommended Draw-Tite Trailer Hitch Receiver For 1969 Chevrolet K10 Pickup

Question

Question:

I have been looking at your website for a trailer hitch and narrowed it down to draw tite 41947 or 41938. I have a 1969 chevy K10 it looks like the 41947 provides a better fitment. can you give me your best recommendation for my model.

asked by: Joe O

0

Expert Reply:

Both the Draw-Tite Ultra Frame Trailer Hitch Receiver # 41947 and Draw-Tite Ultra Frame Trailer Hitch Receiver # 41938 are a confirmed fit for you 1969 Chevrolet K10 as long as you have an 8 Foot bed and both options will require some drilling for the installation.

Since they both install in the same location both will fit the same, with the only differences being that the # 41947 will hang down lower due to the longer side bracket as seen in the included picture.

My preference is the # 41938 due to it having a shorter side bracket meaning less of the hitch will be visible when the installation is complete.

expert reply by: Samuel C

0

click to enlarge

Answer 1

The Draw-Tite Ultra Frame Trailer Hitch Receiver #41938 has a center to center measurement of 30-7/8 inches for the bolt holes from side to side. I've attached a photo to assist.

view full answer...

Answer 2

On the Draw-Tite Trailer Hitch, #41938, the 8 bolts used to attach the hitch each go into the frame rails on the truck. When I spoke with my contact at Draw-Tite he gave a much more clear description of what you will need for this hitch to mount to…

view full answer...

Answer 3

It is very difficult to provide a definite yes or no answer about hitch fit when a service body is involved. I can provide you with some measurements and parameters that would allow you to take some measurements from your truck and determine if the…

view full answer...

Answer 4

Hey Conner, thanks for reaching out! I'm attaching a link to our returns policy for your reference. You aren't the only one in this situation where tire chains like the Titan Chain Snow Tire Chains #TC1530 are required for travel but may not…

view full answer...

Answer 5

Thanks for the picture of the rear of your 1972 Chevy C20. Based on that it looks like you would need a hitch for a drop bumper setup like the Draw Tite part #41504 so that it would clear the bumper.

view full answer...

Answer 6

The Curt Trailer Hitch Receiver part #13028 is designed to fit the following vechiles: - 88-91 CHEVY/GMC 4 DR CREW CAB ONLY - 73-79 FORD 250 CREW CAB - 73-06 CHEVY/GMC FULL SIZE CAB & CHASSIS w 34" FRAME - 73-06 FORD PICKUP: CAB AND CHASSIS…

view full answer...

Answer 7

Hey Dave, yes it does look like the Draw-Tite Max-E-Loader #41001 will fit your 1968 Chevrolet C20. This will fit the 8' bed option with a standard factory bumper, but if you have a 6' bed with the factory bumper then you'd want to use…

view full answer...

Answer 8

The Draw-Tite Max-Frame Trailer Hitch Receiver, #75122, is designed specifically to fit the following vehicles: 1995 - 2005 Chevrolet Astro 1995 - 2005 GMC Safari 1990 - 1994 Chevrolet Astro Extended Body 1990 - 1994 GMC Safari Extended Body But it…

view full answer...

Answer 9

I do see that a deepdrop rear step bumper was offered on your 1972 Chevrolet K-20 pickup. If this is what you have the Curt 3-Piece Trailer Hitch Receiver #C15511 is the receiver I recommend using. Otherwise the Curt Trailer Hitch Receiver #C14082…

view full answer...

Answer 10

I do have some solutions for your 1970 Ford F-250, however, the Curt Trailer Hitch Receiver #C15800 you reference is not a fit for your truck. If your vehicle has the deepdrop style bumper, then I recommend the Curt 3-Piece Trailer Hitch Receiver…

view full answer...

Answer 11

The amperage that the Solera Power Awning Replacement Motor #LC266149 draws will vary based on the awning length and if it is rolling in our out. The motor will pull no more than 15 amps at any given time. When the motor is being wound in it will…

view full answer...

Answer 12

Since you are looking for a heavy-duty trailer hitch, you may be able to use the Curt Class V XD Trailer Hitch, #C15313. This hitch was designed to fit the 2002 GMC Sierra 2500 HD pickup trucks with a frame width of 39 inches. The receiver will sit…

view full answer...

Recommended Draw-Tite Trailer Hitch Receiver For 1969 Chevrolet K10 Pickup

Continue Researching