Brake Controller Plug-and-Play Harness For 2020 Jeep Gladiator
Updated 12/04/2020 | Published 11/30/2020
Products Featured in This Question
Question:
I have a 2020 Jeep Gladiator and the Tekonsha Prodigy P2 brake controller. Which wiring harness do I need to install this on my Gladiator?
asked by: Ed D
Expert Reply:
The Tekonsha Custom Wiring Adapter - Jeep # 3073-P is the product you're looking for.
This adapter plugs into the 5-pin connector on your vehicle's built-in brake control wiring harness. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal.
This product is all you need as long as your 2020 Jeep Gladiator is equipped with the factory towing package.
This adapter requires no cutting or splicing of wires to install. It is designed to plug directly into your electric brake controller for the simplest installation possible. Because there is no hardwiring, installation is not permanent. You can unplug and remove your brake controller at any time and securely stow it away.
If your Gladiator is not equipped with the towing package, you'll need the Universal Installation Kit for Trailer Brake Controller # ETBC7 as well as the plug 'n play adapter for the brake controller.
Product Page this Question was Asked From
Tekonsha Custom Wiring Adapter for Trailer Brake Controllers - Jeep
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Tekonsha Custom Wiring Adapter for Trailer Brake Controllers - Jeep
- Shop: Tekonsha Prodigy P2 Trailer Brake Controller w/ Custom Harness - Up to 4 Axles - Proportional
- Shop: Dexter 12-1/4" Hub-and-Rotor Assembly - Grease - 8 on 6-1/2 - E-Coat - 1/2" Bolts - 7K
- Search Results: brake controller
- Shop: Dexter 12-1/4" Hub-and-Rotor Assembly - Grease - 8 on 6-1/2 - E-Coat - 5/8" Bolts - 7K
- Shop: Dexter 12-1/4" Hub-and-Rotor Assembly - Oil - 8 on 6-1/2 - E-Coat - 1/2" Bolts - 7K
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller w/ Custom Harness - Up to 4 Axles - Proportional
- Video: Review of the Sway Bracket Jackets for Equal-i-zer Weight Distribution Systems
- Shop: Rubber Lip Seal for RV Cargo Doors - Press On - 15' Long x 1-1/8" Wide
- Q&A: Weight Distribution Hitch for Enclosed Car Trailer With 8" Tall Aluminum Frame
- Q&A: How Long is Tekonsha Brake Controller Install Harness 3073-P
- Q&A: Will the Prodigy RF Brake Controller Prevent a Trailer Mounted Battery from Charging
- Q&A: Custom Brake Controller Adapter for a 2024 Jeep Wrangler w/ the Tow Package
- Q&A: Do You Carry The Hardware For LC389910?
- Q&A: Using 1 or 2 Electric Jack Motors for Bulldog Single Speed Jacks with 12,000 Pound Capacity
- Q&A: What is Normal Temperature Rating for Trailer Hubs
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Brake Controller Installation: Starting from Scratch
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps
- Article: RV Sway Control, Stabilization, and Suspension Enhancement
- Article: Trailer Wiring Diagrams