Recommended RV Speakers for Use with Polk Heavy Duty Mechless Stereo

Question

Question:

what speakers do you recommend for this system ?Using it in an RV

asked by: Marc D

0

Expert Reply:

You can use pretty much any speakers with the Jensen # JHD910BT. I recommend using the Jensen Coaxial Indoor RV Speaker - Recessed Mount - 6" Diameter - 50 Watts - Black- Qty 1 # 1103030 as the basic speakers, which are a recessed mounting speaker that will provide high quality, high frequency sound.

I would then pair these speakers with something like the Furrion RV Enclosed Amplified Subwoofer - Surface Mount - 15-3/4" x 9-7/8" - 120 Watt # FSW8P12CF to provide you with a well rounded sound profile when matched with those Jensen speakers. You can also connect this subwoofer to the Furrion Indoor RV Soundbar - Surface Mount - 29-3/4" Wide x 3-7/8" Tall - 40 Watts - Black # FSB24SA2C-BL, which would give you a really robust sound system in your RV. You could likely even forgo the round, recessed mount speakers and just use these two components to give your coach a pretty good system- it really just depends on how much space you've got to fill.

I've linked some review videos of these parts that I recommend checking out.

expert reply by: Erik B

0

Answer 1

It has been measured and the distance between each mounting hole on the #1103030 is 2-7/8" on center. There are 6 mounting holes which would make for a total of 17-1/4" of spacing with straight lines between them. The circumference of a…

view full answer...

Answer 2

Hello Chuck. I do have a good speaker option for you, but the Jensen Indoor RV Speaker #1103030 is 6" in diameter overall, so this is going to be a bit small to fit correctly in a 5-7/8" cutout. Instead, I recommend the Jensen Marine…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Recommended RV Speakers for Use with Polk Heavy Duty Mechless Stereo

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching