Replacement Breakaway Pin and Cable for Esco Brand Switch

Question

Question:

Do you have a cable and pin for an Bright Way breakaway switch? If you do, what is the part number

asked by: Roger W

1

Helpful Expert Reply:

The Replacement 42" Cable for Breakaway Switch # 3802350 is compatible with your certain models of Bright Way breakaway switches. If you only need the cable, this will work for sure. The pin is intended for models 2307, 2308, 2326, 2336, 2337, 2339, 2345, 2346, and 2354.

If you don't know your model, you could replace the switch with # 3802348 since these are universal.

expert reply by: Jason S

1

Answer 1

Hi Gary; the Replacement Cable and Pin for Bright Way Trailer Breakaway Kits #3802350 is the correct replacement pin for your Brightway 2348 #3802348.

view full answer...

Answer 2

The cable part itself you can use from any brand but the pin might be different. If the pin is fine on your breakaway kit and you just need a cable we do carry cables by themselves #RM-8603 I have also included a link to all of the cables with pins…

view full answer...

Answer 3

The Replacement 42" Cable for Breakaway Switch from Bright Way Group, #3802350, will fit most models of ESCO break away switches. If you don't want to take a chance on it not fitting, I would instead recommend replacing the switch with part…

view full answer...

Answer 4

The three sizes of electric trailer drum brakes you referenced, 7-, 10- and 12-inch diameters, are intended for different axle weight capacities. Since each size will presumably have a proportionate weight load it has to stop, their wear rates will…

view full answer...

Answer 5

The front cover of the Bright Way Push-to-Test Trailer Breakaway Kit #3802346 is supposed to swing out like you mentioned. I attached pictures that show the door open. I'd be willing to bet the hinge on the left side of the door isn't fully…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Replacement Breakaway Pin and Cable for Esco Brand Switch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching