Replacement Head and Spring Bars for Fastway e2 Weight Distribution 12,000 lb Capacity

Question

Question:

I’m trying to make sure I order the correct one. Thanks Fast way e2 replacement head/ 12000 pound with square bars from 2017

asked by: Eric M

0

Expert Reply:

For a Fastway e2 weight distribution system the correct head for a 12,000 kit would be the # FA92-02-1255 that you referenced. This matches the picture you attached. Then for replacement spring bars you'd need # FA92-01-1299.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Hey Enoch, we have propane pigtails like the part #100473-24-MBS for a 2 foot long one which is our most popular size. How long of a pigtail do you need? That's pretty scary your leaks like that!

view full answer...

Answer 2

The trunnion head #FA92-02-1255 for your Fastway e2 Weight Distribution w/ 2-Point Sway Control #FA92-00-0800 is the same one used on the 6,000-lb, 8,000-lb, 10,000-lb, or 12,000-lb systems so you can just swap out your spring bars for part…

view full answer...

Answer 3

Definitely! From the looks of your attached pictures, you definitely have a Fastway e2 weight distribution hitch that uses a trunnion spring bar like the #FA92-00-0600. I went ahead and reached out to my contact at Fastway, and he confirmed that the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Head and Spring Bars for Fastway e2 Weight Distribution 12,000 lb Capacity

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching