What is Difference Between Reese Rail Hardware Kits # RP58504 and # RP58430

Question

Question:

I have a 2006 F350 LB with a Pro Series 150000. The hitch is a little over 10 yrs old. What is the difference between the two hardware kits other than $10? Which kit is recommended? Which is preferred?

asked by: Vasilios K

0

Expert Reply:

The two rail hardware kits # RP58504 and the # RP58430 basically fit the rail kits. One includes lock nuts ( # RP58430 ) whereas the # RP58504 does not. But both are listed as fits for same rail kits.

Worth mentioning though is # RP58504 comes with Grade 8 bolts and # RP58430 comes with Grade 5.

expert reply by: Jameson C

0

Answer 1

For your 2015 Ford F-350 Diesel, I recommend starting with the Reese Quick-Install Custom Installation Kit w/ Base Rails for 5th Wheel Trailer Hitches #RP50026-58. These rails and brackets are compatible with the Diesel Exhaust Fluid tank on your…

view full answer...

Answer 2

The correct Reese Custom 5th Wheel Mounting Brackets for your 2011 Ford F-250 is with the part #RP50026. These custom brackets eliminate the need to drill into the frame of your F-250 and will drastically cut down on installation time. For the…

view full answer...

Answer 3

If you are referring the Reese Select Plus 5th Wheel Trailer Hitch #RP30081, then yes all it takes is 4 pins to secure the hitch into the rails installed in the bed of your truck.

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

What is Difference Between Reese Rail Hardware Kits # RP58504 and # RP58430

Continue Researching