Where do I Install the Camco Winterization Kit on my Camper

Question

Question:

Heres what I think is the cold water out of my fresh water tank and into the pump. Will this part fit with no additional parts needed?

asked by: Patrick K

0

Expert Reply:

Yes the Camco RV Water Pump Winterization Kit part # CAM36543 will attach on the blue hose side or down stream side of your pump in the picture. It has the pump adapter and the tape you will need to seal everything up.

expert reply by: Randy B

0

click to enlarge

Mark M.

11/5/2024

Looks to me like it you're 180 degrees off on this one Randy. Putting mine on the intake side to draw antifreeze *into* the system.

Reply

Answer 1

The fitting size of all of the ends of the tee Camco RV Water Pump Winterization Kit #CAM36543 are the same garden hose size fitting of 5/8 inch.

view full answer...

Answer 2

The fitting size of all of the ends of the tee Camco RV Water Pump Winterization Kit #CAM36543 are the same garden hose size fitting of 5/8 inch.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hey Micah! Pacbrake has actually been around for a long time, more than 60 years. We have had customers ask for these air bags in the past, and we've seen them on vehicles coming in. Until now, Firestone has been the go to since their quality is…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 12

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Where do I Install the Camco Winterization Kit on my Camper

Product Page this Question was Asked From

Continue Researching