What Size Handle Does the Replacement Red Claw Knob for Ram Work With

Question

Question:

What is the inside diameter of the HDKB-RED knob? Will it fit on a 1/2 inch shaft?

asked by: Bill A

0

Expert Reply:

The Replacement Red Claw Knob for Ram Topwind Jacks and Gooseneck Couplers part # HDKB-RED is designed for handles with a 1/2" diameter.

expert reply by: Conner L

0

Answer 1

There really is no elegant way to do it. The knob is held in place by a pal nut, which must be removed. It might be possible to get a screwdriver in next to the nut and pry it off, or grasp the end with pliers and rock it back and forth until it can…

view full answer...

Answer 2

We do indeed offer a replacement knob, the part #is BD500246. If you need the entire handle, it is offered as part #BD500180. Although the replacement knob and handle carry the Bulldog brand name, Pro Series is a sister company. I spoke with my…

view full answer...

Answer 3

Hello Kevin, thanks for reaching out. Yes, the Replacement Black Claw Knob #HDKB-BLKF is for a 1/2" diameter jack handle. I went out to our warehouse and measured one and the diameter of the opening is like 0.55". Let me know if there is…

view full answer...

Answer 4

The overall length of the Replacement Topwind Handle w/ Claw Knob for etrailer and Ram Square, Direct Weld Jacks #TJD-7000-HD is 10-1/2 inches. The center to center length is 9 inches. I've attached a photo to assist.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

What Size Handle Does the Replacement Red Claw Knob for Ram Work With

Product Page this Question was Asked From

Continue Researching