Will the Fastway e2 600 Lb Spring Bars Work With Fastway e2 450 lb System

Question

Question:

i have 450lb trunnion spring bars # 92-00-0450 and I want to change to 600lb spring bars # 92-02-0699 will they fit ?

asked by: Paul S

0

Expert Reply:

Yes, the Replacement Trunnion Spring Bar for Fastway e2 Weight Distribution Systems part # FA92-02-0699 which are rated for 600 lbs will work with the Fastway e2 Weight Distribution System part # FA92-00-0450 which is rated for 450 lbs.

expert reply by: Conner L

0

Answer 1

Yes we can help you with a spare tire cover to fit your tire size 235/75R15 which has an overall diameter of about 29-inches and a width of about 9-1/2-inches. You can choose any spare tire cover from those shown on the linked page, all of which fit…

view full answer...

Answer 2

The adjustment of any friction sway control system, including the Reese #83660, is relatively simple. Basically, you will drive with the trailer loaded to determine if more or less tension is needed. Then you will either make it tighter or looser my…

view full answer...

Answer 3

Basically, one friction-style sway control can be used for trailers with up to 6,000-lb GTW. If your trailer's GTW is between 6,000 lbs and 10,000 lbs, you will need two sway-control units, one on each side of the trailer. You will also want to…

view full answer...

Answer 4

Welcome back William! You are getting pretty close to the max capacity of your current set up, so swapping the bars to the Replacement Trunnion Spring Bar for Fastway e2 Weight Distribution Systems - 600 lbs TW #FA92-02-0699 will definitely help you…

view full answer...

Answer 5

Hi Jim; that does indicate it is for the 800/8,000 lb system. They do make a lower rated trunnion #FA92-02-0644 but you don't have to replace yours with the lower rated component. You can swap out your spring bars for the #FA92-02-0699. Are you…

view full answer...

Answer 6

The weight of the Trunnion Spring Bar #FA92-02-0699(13lbs) does need to be considered for the over weight of the trailer and maximum payload but is not used in the calculation of the tongue weight rating for the Fastway e2 Weight Distribution…

view full answer...

Answer 7

I recommend using the Fastway e2 Weight Distribution #FA92-00-0800 for your 7x14 Interstate Loadrunner tandem axle trailer. This hitch is rated for trailers up to 8,000lbs with a tongue weight between 400-800lbs. If your unloaded tongue weight is…

view full answer...

Answer 8

Yes, if the Fastway e2 Weight Distribution System you have now has trunnion spring bars like part #FA92-00-0800 then you can use the Replacement Trunnion Spring Bars part #FA92-01-0699.

view full answer...

Answer 9

To move to a different spring bar weight capacity/range you have to just replace the bars if it's a round bar setup or the bars and the head of the system if it's a trunnion setup. So if you have a round bar setup now you'd want two of…

view full answer...

Answer 10

Your Trunnion Fastway e2 Weight Distribution #FA92-00-0600 is capable of using 6,000lb to 12,000lb bars. 6,000lb Replacement Trunnion Spring Bars #FA92-01-0699, 250-600lbs of tongue weight 8,000lb Replacement Trunnion Spring Bars #FA92-01-0899,…

view full answer...

Answer 11

Yes, the ball plate of the Curt friction sway control part #17200 that you referenced is 3 inches long by 3 inches wide.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Will the Fastway e2 600 Lb Spring Bars Work With Fastway e2 450 lb System

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching